VLSI Architectures for Multi-Gbps Low-Density Parity-Check Decoders PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download VLSI Architectures for Multi-Gbps Low-Density Parity-Check Decoders PDF full book. Access full book title VLSI Architectures for Multi-Gbps Low-Density Parity-Check Decoders by Ahmad Darabiha. Download full books in PDF and EPUB format.
Author: Ahmad Darabiha
Publisher:
ISBN: 9780494398173
Category :
Languages : en
Pages : 228
Get Book Here
Book Description
Near-capacity performance and parallelizable decoding algorithms have made Low-Density Parity Check (LDPC) codes a powerful competitor to previous generations of codes, such as Turbo and Reed Solomon codes, for reliable high-speed digital communications. As a result, they have been adopted in several emerging standards. This thesis investigates VLSI architectures for multi-Gbps power and area-efficient LDPC decoders. To reduce the node-to-node communication complexity, a decoding scheme is proposed in which messages are transferred and computed bit-serially. Also, a broadcasting scheme is proposed in which the traditional computations required in the sum-product and min-sum decoding algorithms are repartitioned between the check and variable node units. To increase decoding throughput, a block interlacing scheme is investigated which is particularly advantageous in fully-parallel LDPC decoders. To increase decoder energy efficiency, an efficient early termination scheme is proposed. In addition, an analysis is given of how increased hardware parallelism coupled with a reduced supply voltage is a particularly effective approach to reduce the power consumption of LDPC decoders. These architectures and circuits are demonstrated in two hardware implementations. Specifically, a 610-Mbps bit-serial fully-parallel (480, 355) LDPC decoder on a single Altera Stratix EP1S80 device is presented. To our knowledge, this is the fastest FPGA-based LDPC decoder reported in the literature. A fabricated 0.13-mum CMOS bit-serial (660, 484) LDPC decoder is also presented. The decoder has a 300 MHz maximum clock frequency and a 3.3 Gbps throughput with a nominal 1.2-V supply and performs within 3 dB of the Shannon limit at a BER of 10-5. With more than 60% power saving gained by early termination, the decoder consumes 10.4 pJ/bit/iteration at Eb=N0=4dB. Coupling early termination with supply voltage scaling results in an even lower energy consumption of 2.7 pJ/bit/iteration with 648 Mbps decoding throughput. The proposed techniques demonstrate that the bit-serial fully-parallel architecture is preferred to memory-based partially-parallel architectures, both in terms of throughput and energy efficiency, for applications such as 10GBase-T which use medium-size LDPC code (e.g., 2048 bit) and require multi-Gbps decoding throughput.
Author: Ahmad Darabiha
Publisher:
ISBN: 9780494398173
Category :
Languages : en
Pages : 228
Get Book Here
Book Description
Near-capacity performance and parallelizable decoding algorithms have made Low-Density Parity Check (LDPC) codes a powerful competitor to previous generations of codes, such as Turbo and Reed Solomon codes, for reliable high-speed digital communications. As a result, they have been adopted in several emerging standards. This thesis investigates VLSI architectures for multi-Gbps power and area-efficient LDPC decoders. To reduce the node-to-node communication complexity, a decoding scheme is proposed in which messages are transferred and computed bit-serially. Also, a broadcasting scheme is proposed in which the traditional computations required in the sum-product and min-sum decoding algorithms are repartitioned between the check and variable node units. To increase decoding throughput, a block interlacing scheme is investigated which is particularly advantageous in fully-parallel LDPC decoders. To increase decoder energy efficiency, an efficient early termination scheme is proposed. In addition, an analysis is given of how increased hardware parallelism coupled with a reduced supply voltage is a particularly effective approach to reduce the power consumption of LDPC decoders. These architectures and circuits are demonstrated in two hardware implementations. Specifically, a 610-Mbps bit-serial fully-parallel (480, 355) LDPC decoder on a single Altera Stratix EP1S80 device is presented. To our knowledge, this is the fastest FPGA-based LDPC decoder reported in the literature. A fabricated 0.13-mum CMOS bit-serial (660, 484) LDPC decoder is also presented. The decoder has a 300 MHz maximum clock frequency and a 3.3 Gbps throughput with a nominal 1.2-V supply and performs within 3 dB of the Shannon limit at a BER of 10-5. With more than 60% power saving gained by early termination, the decoder consumes 10.4 pJ/bit/iteration at Eb=N0=4dB. Coupling early termination with supply voltage scaling results in an even lower energy consumption of 2.7 pJ/bit/iteration with 648 Mbps decoding throughput. The proposed techniques demonstrate that the bit-serial fully-parallel architecture is preferred to memory-based partially-parallel architectures, both in terms of throughput and energy efficiency, for applications such as 10GBase-T which use medium-size LDPC code (e.g., 2048 bit) and require multi-Gbps decoding throughput.
Author: Kiran Kumar Gunnam
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
The VLSI implementation complexity of a low density parity check (LDPC) decoder is largely influenced by the interconnect and the storage requirements. This dissertation presents the decoder architectures for regular and irregular LDPC codes that provide substantial gains over existing academic and commercial implementations. Several structured properties of LDPC codes and decoding algorithms are observed and are used to construct hardware implementation with reduced processing complexity. The proposed architectures utilize an on-the-fly computation paradigm which permits scheduling of the computations in a way that the memory requirements and re-computations are reduced. Using this paradigm, the run-time configurable and multi-rate VLSI architectures for the rate compatible array LDPC codes and irregular block LDPC codes are designed. Rate compatible array codes are considered for DSL applications. Irregular block LDPC codes are proposed for IEEE 802.16e, IEEE 802.11n, and IEEE 802.20. When compared with a recent implementation of an 802.11n LDPC decoder, the proposed decoder reduces the logic complexity by 6.45x and memory complexity by 2x for a given data throughput. When compared to the latest reported multi-rate decoders, this decoder design has an area efficiency of around 5.5x and energy efficiency of 2.6x for a given data throughput. The numbers are normalized for a 180nm CMOS process. Properly designed array codes have low error floors and meet the requirements of magnetic channel and other applications which need several Gbps of data throughput. A high throughput and fixed code architecture for array LDPC codes has been designed. No modification to the code is performed as this can result in high error floors. This parallel decoder architecture has no routing congestion and is scalable for longer block lengths. When compared to the latest fixed code parallel decoders in the literature, this design has an area efficiency of around 36x and an energy efficiency of 3x for a given data throughput. Again, the numbers are normalized for a 180nm CMOS process. In summary, the design and analysis details of the proposed architectures are described in this dissertation. The results from the extensive simulation and VHDL verification on FPGA and ASIC design platforms are also presented.
Author: Zhiqiang Cui
Publisher:
ISBN:
Category : Decoders (Electronics)
Languages : en
Pages : 218
Get Book Here
Book Description
Low-Density Parity-check (LDPC) codes have attracted considerable attention due to their capacity approaching performance over AWGN channel and highly parallelizable decoding schemes. They have been considered in a variety of industry standards for the next generation communication systems. In general, LDPC codes achieve outstanding performance with large codeword lengths (e.g., N>1000 bits), which lead to a linear increase of the size of memory for storing all the soft messages in LDPC decoding. In the next generation communication systems, the target data rates range from a few hundred Mbit/sec to several Gbit/sec. To achieve those very high decoding throughput, a large amount of computation units are required, which will significantly increase the hardware cost and power consumption of LDPC decoders. LDPC codes are decoded using iterative decoding algorithms. The decoding latency and power consumption are linearly proportional to the number of decoding iterations. A decoding approach with fast convergence speed is highly desired in practice. This thesis considers various VLSI design issues of LDPC decoder and develops efficient approaches for reducing memory requirement, low complexity implementation, and high speed decoding of LDPC codes. We propose a memory efficient partially parallel decoder architecture suited for quasi-cyclic LDPC (QC-LDPC) codes using Min-Sum decoding algorithm. We develop an efficient architecture for general permutation matrix based LDPC codes. We have explored various approaches to linearly increase the decoding throughput with a small amount of hardware overhead. We develop a multi-Gbit/sec LDPC decoder architecture for QC-LDPC codes and prototype an enhanced partially parallel decoder architecture for a Euclidian geometry based LDPC code on FPGA. We propose an early stopping scheme and an extended layered decoding method to reduce the number of decoding iterations for undecodable and decodable sequence received from channel. We also propose a low-complexity optimized 2-bit decoding approach which requires comparable implementation complexity to weighted bit flipping based algorithms but has much better decoding performance and faster convergence speed.
Author: Tinoosh Mohsenin
Publisher:
ISBN: 9781124509181
Category :
Languages : en
Pages :
Get Book Here
Book Description
Many emerging and future communication applications require a significant amount of high throughput data processing and operate with decreasing power budgets. This need for greater energy efficiency and improved performance of electronic devices demands a joint optimization of algorithms, architectures, and implementations. Low Density Parity Check (LDPC) decoding has received significant attention due to its superior error correction performance, and has been adopted by recent communication standards such as 10GBASE-T 10 Gigabit Ethernet. Currently high performance LDPC decoders are designed to be dedicated blocks within a System-on-Chip (SoC) and require many processing nodes. These nodes require a large set of interconnect circuitry whose delay and power are wire-dominated circuits. Therefore, low clock rates and increased area are a common result of the codes' inherent irregular and global communication patterns. As the delay and energy costs caused by wires are likely to increase in future fabrication technologies new solutions dealing with future VLSI challenges must be considered. Three novel message-passing decoding algorithms, Split-Row, Multi-Splitand Split-Row Threshold are introduced, which significantly reduce processor logical complexity and local and global interconnections. One conventional and four Split-Row Threshold LDPC decoders compatible with the 10GBASE-T standard are implemented in 65 nm CMOS and presented along with their trade-offs in error correction performance, wire interconnect complexity, decoder area, power dissipation, and speed. For additional power saving, an adaptive wordwidth decoding algorithm is proposed which switches between a 6-bit Normal Mode and a reduced 3-bit Low Power Mode depending on the SNR and decoding iteration. A 16-way Split-Row Threshold with adaptive wordwidth implementation achieves improvements in area, throughput and energy efficiency of 3.9x, 2.6x, and 3.6x respectively, compared to a MinSum Normalized implementation, with an SNR loss of 0.25 dB at BER = 10−7. The decoder occupies a die area of 5.10 mm2, operates up to 185 MHz at 1.3 V, and attains an average throughput of 85.7 Gbps with early-termination. Low power operation at 0.6 V gives a worst case throughput of 9.3 Gbps--above the 6.4 Gbps 10GBASE-T requirement, and an average power of 31 mW.
Author: Yanni Chen
Publisher:
ISBN:
Category :
Languages : en
Pages : 294
Get Book Here
Book Description
Author: Fang Cai
Publisher:
ISBN:
Category :
Languages : en
Pages : 95
Get Book Here
Book Description
Non-binary low-density parity-check (NB-LDPC) codes can achieve better error-correcting performance than binary LDPC codes when the code length is moderate at the cost of higher decoding complexity. The high complexity is mainly caused by the complicated computations in the check node processing and the large memory requirement. In this thesis, two VLSI designs for NB-LDPC decoders based on two novel check node processing schemes are proposed. The first design is based on forward-backward check node processing. A novel scheme and corresponding architecture are developed to implement the elementary step of the check node processing. In our design, layered decoding is applied and only nm less than q messages are kept on each edge of the associated Tanner graph. The computation units and the scheduling of the computations are optimized in the context of layered decoding to reduce the area requirement and increase the speed. This thesis also introduces an overlapped method for the check node processing among different layers to further speed up the decoding. From complexity and latency analysis, our design is much more efficient than any previous design. Our proposed decoder for a (744, 653) code over GF(32) has also been synthesized on a Xilinx Virtex-2 Pro FPGA device. It can achieve a throughput of 9.30 Mbps when 15 decoding iterations are carried out. The second design is based on a proposed trellis based check node processing scheme. The proposed scheme first sorts out a limited number of the most reliable variable-to-check (v-to-c) messages, then the check-to-variable (c-to-v) messages to all connected variable nodes are derived independently from the sorted messages without noticeable performance loss. Compared to the previous iterative forward-backward check node processing, the proposed scheme not only significantly reduced the computation complexity, but eliminated the memory required for storing the intermediate messages generated from the forward and backward processes. Inspired by this novel c-to-v message computation method, we propose to store the most reliable v-to-c messages as 'compressed' c-to-v messages. The c-to-v messages will be recovered from the compressed format when needed. Accordingly, the memory requirement of the overall decoder can be substantially reduced. Compared to the previous Min-max decoder architecture, the proposed design for a (837, 726) code over GF(32) can achieve the same throughput with only 46% of the area.
Author: Vikram Arkalgud Chandrasetty
Publisher: Academic Press
ISBN: 0128112565
Category : Technology & Engineering
Languages : en
Pages : 192
Get Book Here
Book Description
This book takes a practical hands-on approach to developing low complexity algorithms and transforming them into working hardware. It follows a complete design approach – from algorithms to hardware architectures - and addresses some of the challenges associated with their design, providing insight into implementing innovative architectures based on low complexity algorithms.The reader will learn: Modern techniques to design, model and analyze low complexity LDPC algorithms as well as their hardware implementation How to reduce computational complexity and power consumption using computer aided design techniques All aspects of the design spectrum from algorithms to hardware implementation and performance trade-offs Provides extensive treatment of LDPC decoding algorithms and hardware implementations Gives a systematic guidance, giving a basic understanding of LDPC codes and decoding algorithms and providing practical skills in implementing efficient LDPC decoders in hardware Companion website containing C-Programs and MATLAB models for simulating the algorithms, and Verilog HDL codes for hardware modeling and synthesis
Author: Kai Zhang
Publisher:
ISBN:
Category :
Languages : en
Pages : 244
Get Book Here
Book Description
Abstract: The Low-Density Parity-Check (LDPC) codes, which were invented by Gallager back in 1960s, have attracted considerable attentions recently. Compared with other error correction codes, LDPC codes are well suited for wireless, optical, and magnetic recording systems due to their near- Shannon-limit error-correcting capacity, high intrinsic parallelism and high-throughput potentials. With these remarkable characteristics, LDPC codes have been adopted in several recent communication standards such as 802.11n (Wi-Fi), 802.16e (WiMax), 802.15.3c (WPAN), DVB-S2 and CMMB. This dissertation is devoted to exploring efficient VLSI architectures for high-performance LDPC decoders and LDPC-like detectors in sparse inter-symbol interference (ISI) channels. The performance of an LDPC decoder is mainly evaluated by area efficiency, error-correcting capability, throughput and rate flexibility. With this work we investigate tradeoffs between the four performance aspects and develop several decoder architectures to improve one or several performance aspects while maintaining acceptable values for other aspects ... Layered decoding algorithm, which is popular in LDPC decoding, is also adopted in this paper. Simulation results show that the layered decoding doubles the convergence speed of the iterative belief propagation process. Exploring the special structure of the connections between the check nodes and the variable nodes on the factor graph, we propose an effective detector architecture for generic sparse ISI channels to facilitate the practical application of the proposed detection algorithm. The proposed architecture is also reconfigurable in order to switch flexible connections on the factor graph in the time-varying ISI channels.
Author: Mario Milicevic
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Forward error correction enables reliable one-way communication over noisy channels, by transmitting redundant data along with the message in order to detect and resolve errors at the receiver. Low-density parity-check (LDPC) codes achieve superior error-correction performance on Gaussian channels under belief propagation decoding, however, their complex parity-check matrix structure introduces hardware implementation challenges. This thesis explores how the quasi-cyclic structure of LDPC parity-check matrices can be exploited in the design of low-power hardware architectures for multi-Gigabit/second decoders realized in CMOS technology, as well as in the design and construction of multi-edge LDPC codes for long-distance (beyond 100km) quantum cryptography over optical fiber. A frame-interleaved architecture is presented with a path-unrolled message-passing schedule to reduce the complexity of routing interconnect in an integrated circuit decoder implementation. A proof-of-concept silicon test chip was fabricated in the 28nm CMOS technology node. The LDPC decoder chip supports the four codes presented in the IEEE 802.11ad standard, occupies an area of 3.41mm^2, and achieves an energy efficiency of 15pJ/bit while delivering a maximum throughput of 6.78Gb/s, and operating with a 202MHz clock at 0.9V supply. The test chip achieves the highest normalized energy efficiency among published CMOS-based decoders for the IEEE 802.11ad standard. A quasi-cyclic code construction technique is applied to a multi-edge LDPC code with block length of 10^6 bits in order to reduce the latency of LDPC decoding in the key reconciliation step of long-distance quantum key distribution. The GPU-based decoder achieves a maximum information throughput of 7.16Kb/s, and extends the current maximum transmission distance from 100km to 160km with a secret key rate of 4.10 x 10^(-7) bits/pulse under 8-dimensional reconciliation. The GPU-based decoder delivers up to 8.03x higher decoded information throughput over the upper bound on secret key rate for a lossy optical channel, thus demonstrating that key reconciliation with LDPC codes is no longer a post-processing bottleneck in quantum key distribution. The contributions presented in this thesis can be applied to future research in the implementation of silicon-based linear-program decoders for high-reliability channels, and single-chip solutions for quantum key distribution containing integrated photonics and post-processing algorithms.
Author: Xinmiao Zhang
Publisher: CRC Press
ISBN: 1351831224
Category : Technology & Engineering
Languages : en
Pages : 387
Get Book Here
Book Description
Error-correcting codes are ubiquitous. They are adopted in almost every modern digital communication and storage system, such as wireless communications, optical communications, Flash memories, computer hard drives, sensor networks, and deep-space probing. New-generation and emerging applications demand codes with better error-correcting capability. On the other hand, the design and implementation of those high-gain error-correcting codes pose many challenges. They usually involve complex mathematical computations, and mapping them directly to hardware often leads to very high complexity. VLSI Architectures for Modern Error-Correcting Codes serves as a bridge connecting advancements in coding theory to practical hardware implementations. Instead of focusing on circuit-level design techniques, the book highlights integrated algorithmic and architectural transformations that lead to great improvements on throughput, silicon area requirement, and/or power consumption in the hardware implementation. The goal of this book is to provide a comprehensive and systematic review of available techniques and architectures, so that they can be easily followed by system and hardware designers to develop en/decoder implementations that meet error-correcting performance and cost requirements. This book can be also used as a reference for graduate-level courses on VLSI design and error-correcting coding. Particular emphases are placed on hard- and soft-decision Reed-Solomon (RS) and Bose-Chaudhuri-Hocquenghem (BCH) codes, and binary and non-binary low-density parity-check (LDPC) codes. These codes are among the best candidates for modern and emerging applications due to their good error-correcting performance and lower implementation complexity compared to other codes. To help explain the computations and en/decoder architectures, many examples and case studies are included. More importantly, discussions are provided on the advantages and drawbacks of different implementation approaches and architectures.
