Simulation of Gross and Net Erosion of High-Z Materials in the DIII-D Divertor PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Simulation of Gross and Net Erosion of High-Z Materials in the DIII-D Divertor PDF full book. Access full book title Simulation of Gross and Net Erosion of High-Z Materials in the DIII-D Divertor by . Download full books in PDF and EPUB format.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 31
Get Book Here
Book Description
The three-dimensional Monte Carlo code ERO has been used to simulate dedicated DIII-D experiments in which Mo and W samples with different sizes were exposed to controlled and well-diagnosed divertor plasma conditions to measure the gross and net erosion rates. Experimentally, the net erosion rate is significantly reduced due to the high local redeposition probability of eroded high-Z materials, which according to the modelling is mainly controlled by the electric field and plasma density within the Chodura sheath. Similar redeposition ratios were obtained from ERO modelling with three different sheath models for small angles between the magnetic field and the material surface, mainly because of their similar mean ionization lengths. The modelled redeposition ratios are close to the measured value. Decreasing the potential drop across the sheath can suppress both gross and net erosion because sputtering yield is decreased due to lower incident energy while the redeposition ratio is not reduced owing to the higher electron density in the Chodura sheath. Taking into account material mixing in the ERO surface model, the net erosion rate of high-Z materials is shown to be strongly dependent on the carbon impurity concentration in the background plasma; higher carbon concentration can suppress net erosion. As a result, the principal experimental results such as net erosion rate and profile and redeposition ratio are well reproduced by the ERO simulations.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 31
Get Book Here
Book Description
The three-dimensional Monte Carlo code ERO has been used to simulate dedicated DIII-D experiments in which Mo and W samples with different sizes were exposed to controlled and well-diagnosed divertor plasma conditions to measure the gross and net erosion rates. Experimentally, the net erosion rate is significantly reduced due to the high local redeposition probability of eroded high-Z materials, which according to the modelling is mainly controlled by the electric field and plasma density within the Chodura sheath. Similar redeposition ratios were obtained from ERO modelling with three different sheath models for small angles between the magnetic field and the material surface, mainly because of their similar mean ionization lengths. The modelled redeposition ratios are close to the measured value. Decreasing the potential drop across the sheath can suppress both gross and net erosion because sputtering yield is decreased due to lower incident energy while the redeposition ratio is not reduced owing to the higher electron density in the Chodura sheath. Taking into account material mixing in the ERO surface model, the net erosion rate of high-Z materials is shown to be strongly dependent on the carbon impurity concentration in the background plasma; higher carbon concentration can suppress net erosion. As a result, the principal experimental results such as net erosion rate and profile and redeposition ratio are well reproduced by the ERO simulations.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 14
Get Book Here
Book Description
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Net erosion rates of carbon target plates have been measured in situ for the DIII-D lower divertor. The principal method of obtaining this data is the DiMES sample probe. Recent experiments have focused on erosion at the outer strike-point (OSP) of two divertor plasma conditions: attached (T[sub e]> 40 eV) ELMing plasmas, and detached (T[sub e]2 eV) ELMing plasmas. For the attached cases, the erosion rates exceed 10 cm/exposure-year, even with incident heat flux
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 16
Get Book Here
Book Description
The ability to withstand disruptions makes carbon-based materials attractive for use as plasma-facing components in divertors. However, such materials suffer high erosion rates during attached plasma operation which, in high power long pulse machines, would give short component lifetimes and high tritium inventories. The authors present results from recent experiments in DIII-D, in which the Divertor Materials Evaluation System (DiMES) was used to examine erosion and deposition during short exposures to well defined plasma conditions. These studies show that during operation with detached plasmas, produced by gas injection, net erosion is suppressed everywhere in the divertor. Net deposition of carbon with deuterium was observed at the inner and outer strikepoints and in the private-flux region between strikepoints. For these low temperature plasmas (T{sub e}
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 17
Get Book Here
Book Description
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 18
Get Book Here
Book Description
Net erosion rates at the outer strike point of the DIII-D divertor plasma were measured for several materials during quiescent H-mode operation with deuterium plasmas. Materials examined include graphite, beryllium, tungsten, vanadium and molybdenum. For graphite, net erosion rates up to 4 nm/sec were found. Erosion rates for the metals were much smaller than for carbon. Ion fluxes from Langmuir probe measurements were used to predict gross erosion by sputtering. Measured net erosion was much smaller than predicted gross erosion. Transport of metal atoms by the plasma across the divertor surface was also examined. Light atoms were transported farther than heavy atoms as predicted by impurity transport models.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 18
Get Book Here
Book Description
The DiMES (Divertor Material Evaluation Studies) mechanism allows insertion of material samples to the lower divertor floor of the DIII-D tokamak. The main purpose of these studies is to measure erosion rates and redeposition mechanisms under tokamak divertor plasma conditions in order to obtain a physical understanding of the erosion/redeposition processes and to determine its implications for fusion power plant plasma facing components. Thin metal films of Be, W, V, and Mo, were deposited on a Si depth-marked graphite sample and exposed to the steady-state outer strike point on DIII-D.A variety of surface analysis techniques are used to determine the erosion/redeposition of the metals and the carbon after 5--15 seconds of exposure. These short exposure times ensure controlled exposure conditions and the extensive array of DIII-D divertor diagnostics provide a well characterized plasma for modeling efforts. Erosion rates and redeposition lengths are found to decrease with the atomic number of the metallic species, as expected. Under these conditions, the peak net erosion rate for carbon is (approximately) 4 nm/s, with the erosion following the ion flux profile. Comparisons of the measured carbon erosion with REDEP code calculations show good agreement for both the absolute net erosion rate and its spatial variation. Measured erosion rates of the metals are smaller than predicted for sputtering from a bare metal surface, apparently due to effects of carbon deposition on the metal surface. Visible spectroscopic measurements of singly ionized Be have determined that the erosion process reaches steady-state during the exposure.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 16
Get Book Here
Book Description
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 3
Get Book Here
Book Description
Author:
Publisher:
ISBN:
Category : Metals
Languages : en
Pages : 658
Get Book Here
Book Description
