High-pressure Pool-boiling Heat Transfer Enhancement and Mechanism on Engineered Surfaces PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download High-pressure Pool-boiling Heat Transfer Enhancement and Mechanism on Engineered Surfaces PDF full book. Access full book title High-pressure Pool-boiling Heat Transfer Enhancement and Mechanism on Engineered Surfaces by Smreeti Dahariya. Download full books in PDF and EPUB format.
Author: Smreeti Dahariya
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Boiling has received considerable attention in the technology advancement of electronics cooling for high-performance computing applications. Two-phase cooling has an advantage over a single-phase cooling in the high heat removal rate with a small thermal gradient due to the latent heat of vaporization. Many surface modifications have been done in the past including surface roughness, mixed wettability and, porous wick copper play a crucial role in the liquid-vapor phase change heat transfer. However, the mechanisms of high-pressure pool-boiling heat transfer enhancement due to surface modifications has not been well studied or understood. The properties of water, such as the latent heat of vaporization, surface tension, the difference in specific volume of liquid and vapor, decrease at high-pressure. High-pressure pool-boiling heat transfer enhancement is studied fundamentally on various engineered surfaces. The boiling tests are performed at a maximum pressure of 90 psig (620.5 kPa) and then compared to results at 0 psig (0 kPa). The results indicate that the pressure influences the boiling performance through changes in bubble dynamics. The bubble departure diameter, bubble departure frequency, and the active nucleation sites change with pressure. The pool-boiling heat transfer enhancement of a Teflon© coated surface is also experimentally tested, using water as the working fluid. The boiling results are compared with a plain surface at two different pressures, 30 and 45 psig. The maximum heat transfer enhancement is found at the low heat fluxes. At high heat fluxes, a negligible effect is observed in HTC. The primary reasons for the HTC enhancement at low heat fluxes are active nucleation sites at low wall superheat and bubble departure size. The Teflon© coated surface promotes nucleation because of the lower surface energy requirement. The boiling results are also obtained for wick surfaces. The wick surfaces are fabricated using a sintering process. The boiling results are compared with a plain surface. The reasons for enhancements in the pool-boiling performance are primarily due to increased bubble generation, higher bubble release frequency, reduced thermal-hydraulic length modulation, and enhanced thermal conductivity due to the sintered wick layer. The analysis suggests that the Rayleigh-critical wavelength decreases by 4.67 % of varying pressure, which may cause the bubble pinning between the gaps of sintered particles and avoids the bubble coalescence. Changes in the pitch distance indicate that a liquid-vapor phase separation happens at the solid/liquid interface, which impacts the heat-transfer performance significantly. Similarly, the role of the high-pressure over the wicking layer is further analyzed and studied. It is found that the critical flow length, [lambda]u reduces by three times with 200 [mu]m particles. The results suggest that the porous wick layer provides a capillary-assist to liquid flow effect, and delays the surface dry out. The surface modification and the pressure amplify the boiling heat transfer performance. All these reasons may contribute to the CHF, and HTC enhancement in the wicking layer at high-pressure.
Author: Smreeti Dahariya
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Boiling has received considerable attention in the technology advancement of electronics cooling for high-performance computing applications. Two-phase cooling has an advantage over a single-phase cooling in the high heat removal rate with a small thermal gradient due to the latent heat of vaporization. Many surface modifications have been done in the past including surface roughness, mixed wettability and, porous wick copper play a crucial role in the liquid-vapor phase change heat transfer. However, the mechanisms of high-pressure pool-boiling heat transfer enhancement due to surface modifications has not been well studied or understood. The properties of water, such as the latent heat of vaporization, surface tension, the difference in specific volume of liquid and vapor, decrease at high-pressure. High-pressure pool-boiling heat transfer enhancement is studied fundamentally on various engineered surfaces. The boiling tests are performed at a maximum pressure of 90 psig (620.5 kPa) and then compared to results at 0 psig (0 kPa). The results indicate that the pressure influences the boiling performance through changes in bubble dynamics. The bubble departure diameter, bubble departure frequency, and the active nucleation sites change with pressure. The pool-boiling heat transfer enhancement of a Teflon© coated surface is also experimentally tested, using water as the working fluid. The boiling results are compared with a plain surface at two different pressures, 30 and 45 psig. The maximum heat transfer enhancement is found at the low heat fluxes. At high heat fluxes, a negligible effect is observed in HTC. The primary reasons for the HTC enhancement at low heat fluxes are active nucleation sites at low wall superheat and bubble departure size. The Teflon© coated surface promotes nucleation because of the lower surface energy requirement. The boiling results are also obtained for wick surfaces. The wick surfaces are fabricated using a sintering process. The boiling results are compared with a plain surface. The reasons for enhancements in the pool-boiling performance are primarily due to increased bubble generation, higher bubble release frequency, reduced thermal-hydraulic length modulation, and enhanced thermal conductivity due to the sintered wick layer. The analysis suggests that the Rayleigh-critical wavelength decreases by 4.67 % of varying pressure, which may cause the bubble pinning between the gaps of sintered particles and avoids the bubble coalescence. Changes in the pitch distance indicate that a liquid-vapor phase separation happens at the solid/liquid interface, which impacts the heat-transfer performance significantly. Similarly, the role of the high-pressure over the wicking layer is further analyzed and studied. It is found that the critical flow length, [lambda]u reduces by three times with 200 [mu]m particles. The results suggest that the porous wick layer provides a capillary-assist to liquid flow effect, and delays the surface dry out. The surface modification and the pressure amplify the boiling heat transfer performance. All these reasons may contribute to the CHF, and HTC enhancement in the wicking layer at high-pressure.
Author: Nanxi Li
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Boiling is a very effective way of heat transfer due to the latent heat of vaporization. Large amount of heat can be removed as bubbles form and leave the heated surface. Boiling heat transfer has lots of applications both in our daily lives and in the industry. The performance of boiling can be described with two important parameters, i.e. the heat transfer coefficient (HTC) and the critical heat flux (CHF). Enhancing the performance of boiling will greatly increase the efficiency of thermal systems, decrease the size of heat exchangers, and improve the safety of thermal facilities. Boiling heat transfer is an extremely complex process. After over a century of research, the mechanism for the HTC and CHF enhancement is still elusive. Previous research has demonstrated that fluid properties, system pressures, surface properties, and heater properties etc. have huge impact on the performance of boiling. Numerous methods, both active and passive, have been developed to enhance boiling heat transfer. In this work, the effect of pressure was investigated on a plain copper substrate from atmospheric pressure to 45 psig. Boiling heat transfer performance enhancement was then investigated on Teflon© coated copper surfaces, and graphene oxide coated copper surfaces under various system pressures. It was found that both HTC and CHF increases with the system pressure on all three types of surfaces. Enhancement of HTC on the Teflon© coated copper surface is contributed by the decrease in wettability. It is also hypothesized that the enhancement in both HTC and CHF on the graphene oxide coated surface is due to pinning from micro and nanostructures in the graphene oxide coating or non-homogeneous wettability. Condensation and freezing experiments were conducted on engineered surfaces in order to further characterize the pinning effect of non-homogeneous wettability and micro/nano structure of the surface.
Author: Ėduard Mikhaĭlovich Savit︠s︡kiĭ
Publisher:
ISBN:
Category : Aluminum-copper alloys
Languages : en
Pages : 12
Get Book Here
Book Description
Author: Sujoy Kumar Saha
Publisher:
ISBN: 9783030207564
Category : Fluid mechanics
Languages : en
Pages : 121
Get Book Here
Book Description
This Brief concerns heat transfer and pressure drop in heat transfer enhancement for boiling and condensation. The authors divide their topic into six areas: abrasive treatment and coatings, combined structured and porous surfaces, basic principles of boiling mechanism, vapor space condensation, convective vaporization, and forced condensation inside tubes. Within this framework, the book examines range of specific phenomena including abrasive treatment, open grooves, 3D cavities, etched surfaces, electroplating, pierced 3D cover sheets, attached wire and screen promoters, non-wetting coatings, oxide and ceramic coatings, porous surfaces, structured surfaces (integral roughness), combined structured and porous surfaces, composite surfaces, single-tube pool boiling tests, theoretical fundamentals like liquid superheat, effect of cavity shape and contact angle on superheat, entrapment of vapor in cavities, nucleation at a surface cavity, effect of dissolved gases, bubble departure diameter, bubble dynamics, boiling hysteresis and orientation effects, basic principles of boiling mechanism, visualization and mechanism of boiling in subsurface tunnels, and Chien and Webb parametric boiling studies.
Author:
Publisher: Springer
ISBN: 9783319266947
Category : Science
Languages : en
Pages : 0
Get Book Here
Book Description
This Handbook provides researchers, faculty, design engineers in industrial R&D, and practicing engineers in the field concise treatments of advanced and more-recently established topics in thermal science and engineering, with an important emphasis on micro- and nanosystems, not covered in earlier references on applied thermal science, heat transfer or relevant aspects of mechanical/chemical engineering. Major sections address new developments in heat transfer, transport phenomena, single- and multiphase flows with energy transfer, thermal-bioengineering, thermal radiation, combined mode heat transfer, coupled heat and mass transfer, and energy systems. Energy transport at the macro-scale and micro/nano-scales is also included. The internationally recognized team of authors adopt a consistent and systematic approach and writing style, including ample cross reference among topics, offering readers a user-friendly knowledgebase greater than the sum of its parts, perfect for frequent consultation. The Handbook of Thermal Science and Engineering is ideal for academic and professional readers in the traditional and emerging areas of mechanical engineering, chemical engineering, aerospace engineering, bioengineering, electronics fabrication, energy, and manufacturing concerned with the influence thermal phenomena.
Author: N. Zuber
Publisher:
ISBN:
Category : Heat
Languages : en
Pages : 216
Get Book Here
Book Description
Author: Dwight Cooke
Publisher:
ISBN:
Category : Ebullition
Languages : en
Pages : 152
Get Book Here
Book Description
"Pool boiling is of interest in heat transfer applications because of its potential for removing large amount of heat resulting from the latent heat of evaporation and little pressure drop penalty for circulating coolant through the system. However, the heat transfer performance of pool boiling systems is still not comparable to the cooling ability provided by enhanced microchannels operating under single-phase conditions. This investigation focuses on the bubble dynamics and heat transfer on plain and structured microchanneled surfaces under various heat fluxes in an effort to understand the underlying heat transfer mechanism through the use of a high speed camera. In a preliminary study, silicon chips have been tested in the nucleate boiling regime, and beneficial microchannel geometries have been identified. It is determined that heat transfer enhancement occurs because of (i) an increase in surface area and (ii) an improvement in the heat transfer mechanism through the channels functioning as liquid conduits for three side heating. The range for channel size in which the greatest enhancement occurs has been identified as being 200 - 400 [micron] width and 300 - 500 [micron] depth. The second study has been investigated with copper chips, with improvements to the test setup for accurate measurement of surface temperature. Ten chips, in addition to a plain chip have been evaluated for heat transfer performance. It has been determined that surfaces with many, small hydraulic diameter channels enhance the heat transfer as well as surfaces with wide and deep channels. The best performing chip had a record heat transfer coefficient of 269 kW/m2K. The large heat fluxes of over 240 W/cm2 were attained without reaching the critical heat flux condition, because of the open channels on the surface acting as conduits for liquid supply to the nucleation sites. The microchannels prevent surface dryout and critical heat flux (CHF), while the channel width controls the size of the departing bubbles."--Abstract.
Author: VDI Gesellschaft
Publisher: Springer Science & Business Media
ISBN: 3540778764
Category : Science
Languages : en
Pages : 1608
Get Book Here
Book Description
For more than 50 years, the Springer VDI Heat Atlas has been an indispensable working means for engineers dealing with questions of heat transfer. Featuring 50% more content, this new edition covers most fields of heat transfer in industrial and engineering applications. It presents the interrelationships between basic scientific methods, experimental techniques, model-based analysis and their transfer to technical applications.
Author: Indranil M. Joshi
Publisher:
ISBN:
Category : Ebullition
Languages : en
Pages : 71
Get Book Here
Book Description
"The miniaturization trend in electronics has spurred the development of efficient thermal management solutions. Single phase techniques are reliable but are limited by large fluid temperature differences and pressure drop. Two phase cooling has very little pressure drop with large heat absorption capacity. Boiling stands out as one of the most effective methods of heat dissipation which utilizes phase change. However, the design of two-phase systems is limited by the critical heat flux condition where a vapor layer prevents the liquid from contacting the heater surface. The current research study is directed towards increasing the CHF and maintaining low wall superheats to design efficient heat removal systems. In this study, different surface modification techniques are studied with an aim to identify various mechanisms that affect the heat transfer. Different surface enhancements in the form of Circumferential rectangular microchannels(CRM) and fin are used over cylindrical surface. Cylindrical tube with outer diameter of 15 mm was used for testing with water as working fluid. Tubular surface with fin attached performed the best yielding the CHF of 115 W/cm2 at wall superheat of 18oC which translated to an enhancement of 76%. The best performance of 110 W/cm2 at 9 oC without reaching CHF was obtained amongst CRM. Different mechanisms were identified by analyzing the results from pool boiling experiments. Area enhancement and contact line substantially affected the heat transfer performance in CRM. Area enhancement increased performance by providing additional area for heat transfer. Contact line region has higher heat flux. Single bubble growing over multiple grooves has increased contact line density which increases heat transfer performance. Increment in CHF was obtained by employing any one of these surface enhancements. High speed imaging enabled to analyze the behavior of bubble after nucleation on the fin surface thus deciphering the flow modulation over the cylindrical surface. Presence of bubble diverter at the bottom surface ensured higher evaporative momentum force towards the cylindrical surface. This displaced nucleating bubble at the bottom away from the fin, enabling liquid to rewet the surface. This allowed the formation of separate liquid vapor pathways which resulted in increased performance."--Abstract.
Author: S.G. Kandlikar
Publisher: Routledge
ISBN: 1351442198
Category : Science
Languages : en
Pages : 786
Get Book Here
Book Description
Provides a comprehensive coverage of the basic phenomena. It contains twenty-five chapters which cover different aspects of boiling and condensation. First the specific topic or phenomenon is described, followed by a brief survey of previous work, a phenomenological model based on current understanding, and finally a set of recommended design equa
