Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
FITTING END STANDARD DIMENSIONS, 37 DEGREE FLARED TUBE CONNECTION FOR SEAL RING
Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
FITTING END STANDARD DIMENSIONS, FOR BULKHEAD 37 DEGREE FLARED TUBE CONNECTIONS FOR SEAL RING
Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
SEAL RING, 37 DEGREE FLARED TUBE FITTING END
Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
SEAL RING, 37° FLARED TUBE FITTING END
Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
AS1097B HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY.
FITTING END, FLARED TUBE, FOR SEAL RING, STANDARD DIMENSIONS FOR, DESIGN STANDARD
Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
FITTING END, BULKHEAD FLARED TUBE, FOR SEAL RING, STANDARD DIMENSIONS FOR, DESIGN STANDARD
Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
Fittings, 37 Degree Internal Flare, Fluid Connection, Procurement Specification
Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Aerospace Standard (AS) establishes the requirements for 37 degree flared tube fittings or machined internal cone fluid connection fittings for use with 37 degree external cone, spherical nose, and seal ring fittings in all types of aerospace fluid systems (see Section 6). Note 4.5.1.2 revised to remove the statement that destructive testing is required to retain QML status. This requirement is regulated by AC7112.
Fittings, 37° Internal Flare, Fluid Connection, Procurement Specification
Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This SAE Aerospace Standard (AS) establishes the requirements for 37° flared tube fittings or machined internal cone fluid connection fittings for use with 37° external cone, spherical nose and seal ring fittings in all types of aerospace fluid systems (see Section 6). Administrative revision to correct paragraph cross-references throughout the document and applicable document references.
FITTING END, SPHERICAL, 37° FLARED TUBE CONNECTION DESIGN STANDARD
Author: G-3, Aerospace Couplings, Fittings, Hose, Tubing AssembliesPublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
HYDRAULIC TUBE FITTINGS
Author: Hydraulic Tube Fittings CommitteePublisher:
ISBN:
Category :
Languages : en
Pages : 0
Book Description
This standard covers complete general and dimensional specifications for 37 deg flared and flareless types of hydraulic tube fittings and the O-ring bosses and related components with which they assemble. These fittings are intended for general application in hydraulic systems on industrial equipment and commercial products.The 37 deg flared tube fittings shall be as shown in Figs. 5-18 and Tables 3-6. Since the basic design of these fittings is derived from Air Force and Navy Standards for 37 deg flared fittings which meet a performance specification, any future changes should not be detrimental to the design or performance. Dimensions for double and single 37 deg flares on tubing to be used with these fittings are given in Fig. 3 and Table 2 of SAE J533.The flareless tube fittings shall be as shown in Figs. 19-32 and Tables 7-10. The basic design of these fittings is derived from existing military standards.Specifications for straight thread O-ring bosses into which connector and adjustable styles of hydraulic tube fittings assemble are given in Fig. 34 and Table 12. O-ring boss plugs shall be as shown in Fig. 35 and Table 13. Modification of hexagon chamfers on standard fittings when used in MS 33649 (or superseded AND 10050) type O-ring bosses is covered in Fig. 33 and Table 11. For specifications of O-rings used in conjunction with these fittings, see SAE J515.Also included as Appendix A are tables and instructions which may be used for determining the overall lengths, leg lengths, and stock sizes applicable to special size combination fittings not covered in the standard dimensional tabulations.The following general specifications supplement the dimensional data contained in Tables 3-13 with respect to all unspecified detail.
