An Experimental Study of Subcooled Flow Boiling at Elevated Pressure in an Annular Flow Channel PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download An Experimental Study of Subcooled Flow Boiling at Elevated Pressure in an Annular Flow Channel PDF full book. Access full book title An Experimental Study of Subcooled Flow Boiling at Elevated Pressure in an Annular Flow Channel by Pervej Rahman. Download full books in PDF and EPUB format.
Author: Pervej Rahman
Publisher:
ISBN:
Category :
Languages : en
Pages : 106
Get Book Here
Book Description
An experimental setup was developed to study the region of subcooled flow boiling. Multiple studies were carried out to investigate the effects of liquid velocity, pressure, and temperature on the boiling heat transfer of subcooled fluid flowing through a heated annular channel. Water was used as the working fluid and principle of Ohmic heating was used to raise water temperature. The system pressure, heat flux, & mass flux ranged from 101 to 912 kPa, 19 to 155 kW/m2, and 83 to 332 kg/m2-s, respectively. This report contains boiling curves, heat transfer coefficients of various studies and a description of the experimental setup.
Author: Pervej Rahman
Publisher:
ISBN:
Category :
Languages : en
Pages : 106
Get Book Here
Book Description
An experimental setup was developed to study the region of subcooled flow boiling. Multiple studies were carried out to investigate the effects of liquid velocity, pressure, and temperature on the boiling heat transfer of subcooled fluid flowing through a heated annular channel. Water was used as the working fluid and principle of Ohmic heating was used to raise water temperature. The system pressure, heat flux, & mass flux ranged from 101 to 912 kPa, 19 to 155 kW/m2, and 83 to 332 kg/m2-s, respectively. This report contains boiling curves, heat transfer coefficients of various studies and a description of the experimental setup.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 11
Get Book Here
Book Description
Experimental data for static flow instability or flow excursion (FE) at conditions applicable to the Advanced Neutron Source Reactor are very limited. A series of FE tests with light water flowing vertically upward was completed covering a local exit heat flux range of 0.7--18 MW/m2, exit velocity range of 2.8--28.4 m/s, exit pressure range of 0.117--1.7 MPa, and inlet temperature range of 40-- 50°C. Most of the tests were performed in a ''stiff'' (constant flow) system where the instability threshold was detected through the minimum of the pressure-drop curve. A few tests were also conducted using as ''soft'' (constant pressure drop) a system as possible to secure a true FE phenomenon (actual secondary burnout). True critical heat flux experiments under similar conditions were also conducted using a stiff system. The FE data reported in this study considerably extend the velocity range of data presently available worldwide, most of which were obtained at velocities below 10 m/s. The Saha and Zuber correlation had the best fit with the data out of the three correlations compared. However, a modification was necessary to take into account the demonstrated dependence of the St and Nu numbers on subcooling levels, especially in the low subcooling regime. Comparison of Thermal Hydraulic Test Loop (THTL) data, as well as extensive data from other investigators, led to a proposed modification to the Saha and Zuber correlation for onset of significant void, applied to FE prediction. The mean and standard deviation of the THTL data were 0.95 and 15%, respectively, when comparing the THTL data with the original Saha and Zuber correlation, and 0.93 and 10% when comparing them with the modification. Comparison with the worldwide database showed a mean and standard deviation of 1.37 and 53%, respectively, for the original Saha and Zuber correlation and 1.0 and 27% for the modification.
Author: Jun Soo Yoo
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
A series of experimental work to investigate the subcooled boiling flow in a vertical square upward flow channel is described. As experimental methods, high-speed photography and infrared (IR) thermometry were employed simultaneously. The research scope explored includes (i) measurement issues of fundamental bubble parameters through visualization, (ii) experimental methodology to achieve both enhanced two-phase flow visualization and accurate wall temperature measurement, and (iii) measurement of diverse aspects of bubble dynamics as well as wall heat transfer by applying the verified experimental approach. Before producing the actual data, substantial effort was first made to identify the critical measurement issues of fundamental bubble parameters in a forced convective boiling system. Those issues have never been explicitly addressed in previous studies despite the possibly critical impacts on the experimental results. Thus, a series of systematic experimental investigations was performed to uncover those issues and to verify the errors created by not addressing them, based on which more suitable ways of observing and characterizing such parameters through experiments were discussed. Then, an experimental strategy to achieve high-fidelity optical measurements using both high-speed photography and IR thermometry was established. To attain the goal, the important issues such as test section design, IR thermal imaging issues, visualization strategy, wall temperature tracking method, and experimental validations were extensively addressed. Also, the feasibility of current experimental approach was demonstrated through the subcooled flow boiling experiment. Finally, by employing the experimental strategy established, an experimental investigation of the subcooled boiling flow was conducted. The experiment was performed in a vertical square upward flow channel using refrigerant NovecTM 7000, in which a single nucleation site was purposely activated for a fundamental study of subcooled flow boiling process. The various aspects of bubble behavior under different subcooled flow boiling conditions were examined using both micro- and macroscopic views of high-speed cameras while measuring the wall temperature/heat flux with IR thermometry. Additionally, based on the measurements of various bubble parameters as well as wall heat transfer, relevant relations among those parameters and the underlying mechanisms were intensively discussed. The electronic version of this dissertation is accessible from http://hdl.handle.net/1969.1/155042
Author:
Publisher:
ISBN:
Category : Heat
Languages : en
Pages : 38
Get Book Here
Book Description
Author: Ling Zou
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Subcooled flow boiling is generally characterized by high heat transfer capacity and low wall superheat, which is essential for cooling applications requiring high heat transfer rate, such as nuclear reactors and fossil boilers. In this study, subcooled flow boiling on copper and stainless steel heating surfaces was experimentally investigated from both macroscopic and microscopic points of view. Flow boiling heat flux and heat transfer coefficient were experimentally measured on both surfaces under different conditions, such as pressure, flow rate and inlet subcooling. Significant boiling heat transfer coefficient differences were found between the copper and the stainless steel heating surfaces. To explain the different flow boiling behaviors on these two heating surfaces, nucleation site density and bubble dynamics were visually observed and measured at different experimental conditions utilizing a high-speed digital video camera. These two parameters are believed to be keys in determining flow boiling heat flux. Wall superheat, critical cavity size and wall heat flux were used to correlate with nucleation site density data. Among them, wall heat flux shows the best correlation for eliminating both pressure and surface property effects. The observed nucleation site distribution shows a random distribution. When compared to the spatial Poisson distribution, similarity between them was found, while the measured nucleation site distribution is more uniform. From experimental observations, for the two surface materials investigated, which have similar surface wettability but sharply different thermal properties, bubble dynamics displayed fairly similar behavior. The obtained experimental results indicate that thermal conductivity of heating surface material plays an important role in boiling heat transfer. This is due to thermal conductivity having a significant impact on the lateral heat conduction at the heating surface and consequently temperature uniformity of the heating surface. A model was then developed and solved numerically for heat conduction at the heating surface when bubbles are present. Several key parameters which impact lateral heat conduction and surface temperature profile were studied. These parameters include material thermal conductivity, bubble size, heating surface thickness, etc. Numerical results show that, temperature profile on the heating surface tends to be more uniform and have a lower average value on a heating surface with higher thermal conductivity, which agrees well with the experimental observation.
Author: Nathan Eamon Colgan
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Author: John Ralph McDonald
Publisher:
ISBN:
Category : Fluid dynamics
Languages : en
Pages : 254
Get Book Here
Book Description
Author: Jianyun Shuai
Publisher: Cuvillier Verlag
ISBN: 3865372406
Category :
Languages : en
Pages : 131
Get Book Here
Book Description
Author: L S Tong
Publisher: Routledge
ISBN: 1351463373
Category : Science
Languages : en
Pages : 572
Get Book Here
Book Description
Completely updated, this graduate text describes the current state of boiling heat transfer and two-phase flow, in terms through which students can attain a consistent understanding. Prediction of real or potential boiling heat transfer behaviour, both in steady and transient states, is covered to aid engineering design of reliable and effective systems.
Author: John G. Collier
Publisher: Clarendon Press
ISBN: 0191591262
Category :
Languages : en
Pages : 646
Get Book Here
Book Description
* Third edition of a well-known and well established text both in industry and for teaching * Fully up-to-date and includes extra problems This book is an aid to heat exchanger design written primarily for design and development engineers in the chemical process, power generation, and refrigeration industries. It provides a comprehensive reference on two-phase flows, boiling, and condensation. The text covers all the latest advances like flows over tube bundles and two-phase heat transfer regarding refrigerants and petrochemicals. Another feature of this third edition is many new problems at chapter ends to enhance its use as a teaching text for graduate and post-graduate courses on two-phase flow and heat transfer. - ;This book is written for practising engineers as a comprehensive reference on two-phase flows, boiling, and condensation. It deals with methods for estimating two-phase flow pressure drops and heat transfer rates. It is a well-known reference book in its third edition and is also used as a text for advanced university courses. Both authors write from practical experience as both are professional engineers. -
