Oxidation behaviour of MCrAlX coatings PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Oxidation behaviour of MCrAlX coatings PDF full book. Access full book title Oxidation behaviour of MCrAlX coatings by Pimin Zhang. Download full books in PDF and EPUB format.
Author: Pimin Zhang
Publisher: Linköping University Electronic Press
ISBN: 9176853810
Category :
Languages : en
Pages : 79
Get Book Here
Book Description
MCrAlY coatings (M=Ni and/or Co) have been widely used for the protection of superalloy components against oxidation and hot corrosion in the hot sections of gas turbines. The drive to improve engine combustion efficiency while reducing emissions by increasing the operation temperature brings a big challenge for coating design. As a result, the need for improvement of MCrAlY coatings for better oxidation resistance is essential. Formation of a stable, dense, continuous, and slow-growing ?-Al2O3 layer, on the MCrAlY coating surface, is the key to oxidation protection, since the protective ?-Al2O3 scale offers superior oxidation resistance due to its lower oxygen-diffusion rate as compared with other oxides. The ability of a MCrAlY coating to form and maintain such a protective scale depends on the coating composition and microstructure, and can be improved through optimization of deposition parameters, modification of coating surface conditions, and so on. Part of this thesis work focuses on studying the effect of post-deposition surface treatments on the oxidation behavior of MCrAlX coatings (X can be yttrium and/or other minor alloying elements). The aim is to gain fundamental understanding of alumina scale evolution during oxidation which is important for achieving improved oxidation resistance of MCrAlX coatings. Oxide scale formed on coatings at initial oxidation stage and the effect of surface treatment were investigated by a multi-approach study combining photo-stimulated luminescence, microstructural observation and weight gain. Results showed that both mechanically polished and shot-peened coatings exhibited superior performance due to rapid formation of ?-Al2O3 fully covering the coating and suppressing growth of transient alumina, assisted by the high density of ?-Al2O3 nuclei on surface treatment induced defects. The early development of a two-layer alumina scale, consisting of an inward-grown inner ?-Al2O3 layer and an outer layer transformed from outward-grown transient alumina, resulted in a higher oxide growth rate of the as-sprayed coating. The positive effect of the surface treatments on retarding oxide scale growth and suppressing formation of spinel was also observed in oxidation test up to 1000 hrs. As the oxidation proceeds to the close-to-end stage, a reliable criterion to estimate the capability of coating to form ?-Al2O3 is of great importance to accurately evaluate coating lifetime, which is the aim of the other part of the thesis work. Survey of published results on a number of binary Ni-Al and ternary Ni-Cr-Al, Ni-Al-Si systems shows that the empirical Al-concentration based criterion is inadequate to properly predict the formation of a continuous ?-Al2O3 scale. On the other hand, correlating the corresponding Al-activity data, calculated from measured chemical compositions using the Thermo-Calc software, to the experimental oxidation results has revealed a temperature dependent, critical Al-activity value for forming continuous ?-Al2O3 scale. To validate the criterion, long-term oxidation tests were performed on five MCrAlX coatings with varying compositions and the implementation of the Al-activity based criterion on these coatings successfully predicted ?-Al2O3 formation, showing a good agreement with experiment results.
Author: Pimin Zhang
Publisher: Linköping University Electronic Press
ISBN: 9176853810
Category :
Languages : en
Pages : 79
Get Book Here
Book Description
MCrAlY coatings (M=Ni and/or Co) have been widely used for the protection of superalloy components against oxidation and hot corrosion in the hot sections of gas turbines. The drive to improve engine combustion efficiency while reducing emissions by increasing the operation temperature brings a big challenge for coating design. As a result, the need for improvement of MCrAlY coatings for better oxidation resistance is essential. Formation of a stable, dense, continuous, and slow-growing ?-Al2O3 layer, on the MCrAlY coating surface, is the key to oxidation protection, since the protective ?-Al2O3 scale offers superior oxidation resistance due to its lower oxygen-diffusion rate as compared with other oxides. The ability of a MCrAlY coating to form and maintain such a protective scale depends on the coating composition and microstructure, and can be improved through optimization of deposition parameters, modification of coating surface conditions, and so on. Part of this thesis work focuses on studying the effect of post-deposition surface treatments on the oxidation behavior of MCrAlX coatings (X can be yttrium and/or other minor alloying elements). The aim is to gain fundamental understanding of alumina scale evolution during oxidation which is important for achieving improved oxidation resistance of MCrAlX coatings. Oxide scale formed on coatings at initial oxidation stage and the effect of surface treatment were investigated by a multi-approach study combining photo-stimulated luminescence, microstructural observation and weight gain. Results showed that both mechanically polished and shot-peened coatings exhibited superior performance due to rapid formation of ?-Al2O3 fully covering the coating and suppressing growth of transient alumina, assisted by the high density of ?-Al2O3 nuclei on surface treatment induced defects. The early development of a two-layer alumina scale, consisting of an inward-grown inner ?-Al2O3 layer and an outer layer transformed from outward-grown transient alumina, resulted in a higher oxide growth rate of the as-sprayed coating. The positive effect of the surface treatments on retarding oxide scale growth and suppressing formation of spinel was also observed in oxidation test up to 1000 hrs. As the oxidation proceeds to the close-to-end stage, a reliable criterion to estimate the capability of coating to form ?-Al2O3 is of great importance to accurately evaluate coating lifetime, which is the aim of the other part of the thesis work. Survey of published results on a number of binary Ni-Al and ternary Ni-Cr-Al, Ni-Al-Si systems shows that the empirical Al-concentration based criterion is inadequate to properly predict the formation of a continuous ?-Al2O3 scale. On the other hand, correlating the corresponding Al-activity data, calculated from measured chemical compositions using the Thermo-Calc software, to the experimental oxidation results has revealed a temperature dependent, critical Al-activity value for forming continuous ?-Al2O3 scale. To validate the criterion, long-term oxidation tests were performed on five MCrAlX coatings with varying compositions and the implementation of the Al-activity based criterion on these coatings successfully predicted ?-Al2O3 formation, showing a good agreement with experiment results.
Author: Pimin Zhang
Publisher: Linköping University Electronic Press
ISBN: 9175190052
Category :
Languages : en
Pages : 80
Get Book Here
Book Description
MCrAlY coatings (M=Ni and/or Co) are widely used for the protection of superalloy components against oxidation and hot corrosion in the hot sections of gas turbines. The drive for coating systems to bestow adequate oxidation and corrosion resistance upon the components becomes urgent as an inevitable result of the necessary improvement in engine combustion efficiency and service lifetime. Through the careful design of the composition, MCrAlY coating performance can be optimized to meet the needs under different service conditions and component materials, therefore, “MCrAlX”, with “X” stands for the minor alloying elements, is used to highlight the effect. In the present thesis, the performance of new MCrAlX coatings is investigated with respect to oxidation, hot corrosion and interactions between coating-superalloy substrates. Oxidation of MCrAlX coatings can be generally categorized into initial, steady and close-to-end stages. Coating performance can be affected by various factors at different stages, therefore, experiments were designed by targeting the oxidation stages. Investigation on the initial stage oxidation behavior of MCrAlY coatings with post-deposition surface treatments reveals the different growth mechanisms of alumina scales. Surface treatments significantly reduce the alumina growth rate by suppressing transient alumina development and aiding the early formation of ?-Al2O3, which improves the long-term oxidation performance of the coating. Similarly, the modification of minor alloy elements in MCrAlX coatings also serves the purpose. The oxidation behavior of new MCrAlX coatings was investigated at the steady oxidation stage, followed by the microstructure observation, thermodynamic and kinetic simulations. As an alternative reactive element addition of Y, Ce shows a negative effect on the formation of columnar alumina scales of high strain tolerance. In comparison, Fe or Ru addition shows no influence on alumina growth, rather than strengthening the phase stability in the coating and reducing the interdiffusion between coating-substrate through different mechanisms. As the oxidation proceeds to the close-to-end stage, a reliable criterion to estimate the capability of coating to form ?-Al2O3 is of great importance to accurately evaluate coating lifetime. A temperature-dependent critical Al-activity criterion was proposed to better predict the formation of a continuous ?-Al2O3 scale based on correction of elemental activity using thermodynamic database to replace the empirical Al-concentration based criterion. Severe interdiffusion occurs between coating-substrate during high temperature oxidation, accelerating the degradation of the system. Interdiffusion behavior of diffusion couples of superalloys-MCrAlX coatings were examined. It is highlighted that the recrystallization of superficial layer of the substrate contributes to the secondary reaction zone formation and element interdiffusion controls subsequent zone thickening. Study on Type I hot corrosion behavior of new MCrAlX coatings shows that the addition of Fe has no influence on basic fluxing reactions before severe Al depletion from the coating occurs. Instead, it boosts the “effective” Al supply of coating by shifting the equilibrium concentration of Al in the ? phase to a low Al level. Besides, the pre-mature coating degradation at the coating-substrate interface was due to the fast growth of corrosion products from substrate induced large local volume expansions, resulting in early coating spallation. MCrAlY ytbeläggningar (M=Ni och/eller Co) används ofta för att skydda komponenter tillverkade av superlegeringar mot oxidation samt högtemperaturskorrosion i de heta gasturbindelarna. Förbättrad förbränningseffektivitet och livslängd hos gasturbiner, gör att ytbeläggningssystemen måste besitta adekvata oxidations- och korrosionsmotstånd. Genom att omsorgsfullt utforma den kemiska sammansättningen hos MCrAlY ytbeläggningar kan deras prestanda optimeras för att möta kraven från olika driftförhållanden samt olika substratmaterial, därför används beteckningen "MCrAlX" för att belysa förändringar av den kemiska kompositionen, där "X" står för reaktiva legeringsämnen som tillsätts i mindre mängder. I denna avhandling undersöks prestandan hos en ny MCrAlX ytbeläggning med hänsyn till oxidation, högtemperaturskorrosion och interaktionen mellan ytbeläggningen och superlegeringssubstratet. Oxidation av MCrAlX ytbeläggningar kan generellt kategoriseras i tre faser; initiala, stabila och nära-slutet fasen. Ytbeläggningens prestanda kan påverkas av olika faktorer vid de olika faserna, därför utformades olika experiment för att undersöka de olika oxidationsfaserna. Undersökningen av den initiala fasen av oxidationsbeteendet hos MCrAlX ytbeläggningar som genomgått ytbehandlingar efter ytbeläggningsdeponeringen avslöjade olika tillväxtmekanismer hos aluminiumoxidskikten. Aluminiumoxidens tillväxthastighet reducerades signifikant av ytbehandlingarna, detta genom att undertrycka utvecklingen av övergående aluminiumoxid och bistå den tidiga tillväxten av ?-Al2O3, vilket förbättrar ytbeläggningens oxidationsprestanda långsiktigt. De reaktiva legeringsämnena som tillsätts i mindre mänger påverkar ytbeläggningens oxidationsprestanda på liknande sätt. Oxidationsbeteendet hos de nya MCrAlX ytbeläggningarna i den stabila fasen följdes av mikrostrukturundersökning, termodynamiska och kinetiska simuleringar. Det framkom att Ce visar en negativ effekt på bildandet av kolumnära aluminiumoxidskikt med hög töjningstolerans som alternativt reaktivt legeringsämne till Y. Jämförelsevis ger Fe- eller Ru-tillsatser ingen påverkan på aluminiumoxidtillväxten, förutom att det förstärker fasstabiliteten i ytbeläggningen samt genom olika mekanismer reducerar interdiffusionen mellan ytbeläggningen och substratet. När oxidationsprocessen kommit till nära-slutet fasen, är det viktigt att uppskatta kapaciteten hos en ytbeläggning att bilda ?-Al2O3, detta då det är ett tillförlitligt kriterium för att noggrant kunna utvärdera ytbeläggningens livslängd. Därför föreslogs ett temperaturberoende kriterium för kritisk Al-aktivitet för att bättre kunna förutsäga bildandet av ett kontinuerligt ?-Al2O3-skikt. Kriteriet baserades på korrigering av legeringsämnens aktivitet genom att använda en termodynamisk databas, detta för att ersätta det empiriska Al-koncentrations baserade kriteriet. Vid högtemperatursoxidation sker en omfattande interdiffusion mellan ytbeläggningen och substratet, vilket accelererar degraderingen av ytbeläggningssystemet. Därför har interdiffusionsbeteendet mellan superlegeringssubstratet och MCrAlX ytbeläggningen undersökts i denna avhandling. Det framkom att rekristallisationen av ytliga skikt av substratet bidrar till formationen av den sekundära reaktionszonen och att interdiffusion kontrollerar zonens efterföljande tjocklektillväxt. Undersökningen av Typ I högtemperaturskorrosionsbeteendet hos en ny MCrAlX ytbeläggning visar att legeringstillägg av Fe inte påverkar de grundläggande flödesreaktionerna innan en kritisk Al utarmning sker i ytbeläggningen. Istället stimulerar det tillförseln av Al genom att skifta jämviktskoncentrationen av Al i ? fasen till en låg nivå av Al. Det framkom också att den tidiga degraderingen av ytbeläggningen vid gränsskiktet mellan ytbeläggningen och substratet kommer av att den snabba tillväxten av korrosionsprodukter från substratet inducerade en stor lokal volymsutvidgning, vilket ledde till tidig ytbeläggningsspallation.
Author: Shiladitya Paul
Publisher: MDPI
ISBN: 3039361740
Category : Technology & Engineering
Languages : en
Pages : 234
Get Book Here
Book Description
The operation of numerous components that are critical to safety in industries around the world relies on protective coatings. These coatings often allow process equipment to serve a purpose in environments well beyond the operational limit of the uncoated components. Durability, ease of application, repairability, reliability and long-term performance of such coatings are all key to their application. Therefore, this book, Coatings for Harsh Environments, is devoted to research and review articles on the metallic, non-metallic and composite coatings used in aggressive environments. In particular, the topics of interest include, but are not limited to: coatings for high temperature and molten salt applications; thermal spray and cold spray coatings for aggressive environments; corrosion, wear and cavitation resistant coatings; coatings for mitigating marine corrosion; coatings for chemical and petrochemical plants; thermal barrier coatings.
Author: Agnieszka Szczotok
Publisher: Trans Tech Publications Ltd
ISBN: 3038139920
Category : Technology & Engineering
Languages : en
Pages : 268
Get Book Here
Book Description
Selected, peer reviewed papers from the IX International Conference on STERMAT 2012: Stereology and Image Analysis in Materials Science, September 3 - 6, 2012, Zakopane, Poland
Author: Dongming Zhu
Publisher: John Wiley & Sons
ISBN: 0470291737
Category : Technology & Engineering
Languages : en
Pages : 334
Get Book Here
Book Description
Recent advances in coating development, processing, microstructure and property characterization, and life prediction are included in this book, which came from the proceedings of the 30th International Conference on Advanced Ceramics and Composites, January 22-27, 2006, Cocoa Beach, Florida. Organized and sponsored by The American Ceramic Society and The American Ceramic Society's Engineering Ceramics Division in conjunction with the Nuclear and Environmental Technology Division.. Integrated structural, environmental properties and functionality through advanced coating processing and structural design are emphasized in this book.
Author: ACerS (American Ceramics Society, The)
Publisher: John Wiley & Sons
ISBN: 9780470526248
Category : Technology & Engineering
Languages : en
Pages : 628
Get Book Here
Book Description
This edition of the Progress in Ceramic Technology series compiles articles published on thermal barrier coatings (TBCs) by The American Ceramic Society (ACerS). It collects in one resource the current research papers on materials-related aspects of thermal barrier coatings and associated technologies. Logically organized and carefully selected, the papers in this edition divide into six categories: Applications Material Improvements and Novel Compositions Developments in Processing Mechanical Properties Thermal Properties Citations follow each title in the table of contents, making this a key resource for professionals and academia.
Author: Roger C. Reed
Publisher: Cambridge University Press
ISBN: 1139458639
Category : Technology & Engineering
Languages : en
Pages : 363
Get Book Here
Book Description
Superalloys are unique high-temperature materials used in gas turbine engines, which display excellent resistance to mechanical and chemical degradation. This book introduces the metallurgical principles which have guided their development. Suitable for graduate students and researchers, it includes exercises and additional resources at www.cambridge.org/9780521859042.
Author:
Publisher:
ISBN:
Category : Condensed matter
Languages : en
Pages : 444
Get Book Here
Book Description
Author: Sudhangshu Bose
Publisher: Butterworth-Heinemann
ISBN: 0128047437
Category : Technology & Engineering
Languages : en
Pages : 418
Get Book Here
Book Description
High Temperature Coatings, Second Edition, demonstrates how to counteract the thermal effects of rapid corrosion and degradation of exposed materials and equipment that can occur under high operating temperatures. This is the first true practical guide on the use of thermally protective coatings for high-temperature applications, including the latest developments in materials used for protective coatings. It covers the make-up and behavior of such materials under thermal stress and the methods used for applying them to specific types of substrates, as well as invaluable advice on inspection and repair of existing thermal coatings. With his long experience in the aerospace gas turbine industry, the author has compiled the very latest in coating materials and coating technologies, as well as hard-to-find guidance on maintaining and repairing thermal coatings, including appropriate inspection protocols. The book is supplemented with the latest reference information and additional support to help readers find more application- and industry-type coatings specifications and uses. - Offers an overview of the underlying fundamental concepts of thermally-protective coatings, including thermodynamics, energy kinetics, crystallography and equilibrium phases - Covers essential chemistry and physics of underlying substrates, including steels, nickel-iron alloys, nickel-cobalt alloys and titanium alloys - Provides detailed guidance on a wide variety of coating types, including those used against high temperature corrosion and oxidative degradation and thermal barrier coatings
Author: Stefano Gialanella
Publisher: Springer Nature
ISBN: 3030244407
Category : Technology & Engineering
Languages : en
Pages : 583
Get Book Here
Book Description
This book presents an up-to-date overview on the main classes of metallic materials currently used in aeronautical structures and propulsion engines and discusses other materials of potential interest for structural aerospace applications. The coverage encompasses light alloys such as aluminum-, magnesium-, and titanium-based alloys, including titanium aluminides; steels; superalloys; oxide dispersion strengthened alloys; refractory alloys; and related systems such as laminate composites. In each chapter, materials properties and relevant technological aspects, including processing, are presented. Individual chapters focus on coatings for gas turbine engines and hot corrosion of alloys and coatings. Readers will also find consideration of applications in aerospace-related fields. The book takes full account of the impact of energy saving and environmental issues on materials development, reflecting the major shifts that have occurred in the motivations guiding research efforts into the development of new materials systems. Aerospace Alloys will be a valuable reference for graduate students on materials science and engineering courses and will also provide useful information for engineers working in the aerospace, metallurgical, and energy production industries.
