Author: Malav Hemant Thakore
Publisher:
ISBN: 9780438392212
Category : Automobiles
Languages : en
Pages : 108
Get Book Here
Book Description
In the search for cleaner and greener power generation systems, researchers are relentlessly searching for a new engine technology that can perform at a higher efficiency with lower environmentally unsafe gases and particulate matter emissions. A Homogeneous Charge Compression Ignition (HCCI) is one such class of engines, which use high compression ratio to ignite pre-mixed homogeneous air-fuel mixture without the need for any spark plugs. HCCI engines have been drawing attention due to its 1) high operating efficiency and 2) low nitrogen oxide (NOX) and particulate matters (PM) emissions because of lower combustion temperatures. One of the major challenges associated with the HCCI engine is the very rapid combustion rate that results in very high rate of pressure rise and high rate of heat release. One way to address this issue is to reduce the combustion temperature by inducting exhaust gas recirculation (EGR) inside the combustion chamber to dilute the reactant mixture and subsequently lower the reaction rate, operating temperature, and harmful emissions. EGR gases are used to increase the heat capacity of the burned gases for a given quantity of heat release, which in turn lowers the combustion temperature. Particularly, in a four-stroke HCCI engine, hot EGR gases enhance combustion process, mainly due to the high temperature of the intake mixture. In study, a comprehensive simulation analysis of the HCCI engine is carried out using a CFD model that includes solution of three-dimensional RANS equations and turbulent closure model along with the detailed chemical kinetics and non-isothermal wall heat loss to show a quantitative evaluation of the sensitivity of the EGR rate on the heat-release rates (HRR), engine efficiency, and emission.
Author: Michael Y. Au
Publisher:
ISBN:
Category :
Languages : en
Pages : 200
Get Book Here
Book Description
Author: National Research Council
Publisher: National Academies Press
ISBN: 0309373913
Category : Science
Languages : en
Pages : 812
Get Book Here
Book Description
The light-duty vehicle fleet is expected to undergo substantial technological changes over the next several decades. New powertrain designs, alternative fuels, advanced materials and significant changes to the vehicle body are being driven by increasingly stringent fuel economy and greenhouse gas emission standards. By the end of the next decade, cars and light-duty trucks will be more fuel efficient, weigh less, emit less air pollutants, have more safety features, and will be more expensive to purchase relative to current vehicles. Though the gasoline-powered spark ignition engine will continue to be the dominant powertrain configuration even through 2030, such vehicles will be equipped with advanced technologies, materials, electronics and controls, and aerodynamics. And by 2030, the deployment of alternative methods to propel and fuel vehicles and alternative modes of transportation, including autonomous vehicles, will be well underway. What are these new technologies - how will they work, and will some technologies be more effective than others? Written to inform The United States Department of Transportation's National Highway Traffic Safety Administration (NHTSA) and Environmental Protection Agency (EPA) Corporate Average Fuel Economy (CAFE) and greenhouse gas (GHG) emission standards, this new report from the National Research Council is a technical evaluation of costs, benefits, and implementation issues of fuel reduction technologies for next-generation light-duty vehicles. Cost, Effectiveness, and Deployment of Fuel Economy Technologies for Light-Duty Vehicles estimates the cost, potential efficiency improvements, and barriers to commercial deployment of technologies that might be employed from 2020 to 2030. This report describes these promising technologies and makes recommendations for their inclusion on the list of technologies applicable for the 2017-2025 CAFE standards.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
A homogeneous charge compression ignition engine operates by injecting liquid fuel directly in a combustion chamber, and mixing the fuel with recirculated exhaust and fresh air through an auto ignition condition of the fuel. The engine includes at least one turbocharger for extracting energy from the engine exhaust and using that energy to boost intake pressure of recirculated exhaust gas and fresh air. Elevated proportions of exhaust gas recirculated to the engine are attained by throttling the fresh air inlet supply. These elevated exhaust gas recirculation rates allow the HCCI engine to be operated at higher speeds and loads rendering the HCCI engine a more viable alternative to a conventional diesel engine.
Author: Hsien-Hsin Liao
Publisher: Stanford University
ISBN:
Category :
Languages : en
Pages : 201
Get Book Here
Book Description
There has been an enormous global research effort to alleviate the current and projected environmental consequences incurred by internal combustion (IC) engines, the dominant propulsion systems in ground vehicles. Two technologies have the potential to improve the efficiency and emissions of IC engines in the near future: variable valve actuation (VVA) and homogeneous charge compression ignition (HCCI). IC engines equipped with VVA systems are proven to show better performance by adjusting the valve lift and timing appropriately. An electro-hydraulic valve system (EHVS) is a type of VVA system that possesses full flexibility, i.e., the ability to change the valve lift and timing independently and continuously, making it an ideal rapid prototyping tool in a research environment. Unfortunately, an EHVS typically shows a significant response time delay that limits the achievable closed-loop bandwidth and, as a result, shows poor tracking performance. In this thesis, a control framework that includes system identification, feedback control design, and repetitive control design is presented. The combined control law shows excellent performance with a root-mean-square tracking error below 40 [Mu]m over a maximum valve lift of 4 mm. A stability analysis is also provided to show that the mean tracking error converges to zero asymptotically with the combined control law. HCCI, the other technology presented in this thesis, is a combustion strategy initiated by compressing a homogeneous air-fuel mixture to auto-ignition, therefore, ignition occurs at multiple points inside the cylinder without noticeable flame propagation. The result is rapid combustion with low peak in-cylinder temperature, which gives HCCI improved efficiency and reduces NOx formation. To initiate HCCI with a typical compression ratio, the sensible energy of the mixture needs to be high compared to a spark ignited (SI) strategy. One approach to achieve this, called recompression HCCI, is by closing the exhaust valve early to trap a portion of the exhaust gas in the cylinder. Unlike a SI or Diesel strategy, HCCI lacks an explicit combustion trigger, as autoignition is governed by chemical kinetics. Therefore, the thermo-chemical conditions of the air-fuel mixture need to be carefully controlled for HCCI to occur at the desired timing. Compounding this challenge in recompression HCCI is the re-utilization of the exhaust gas which creates cycle-to-cycle coupling. Furthermore, the coupling characteristics can change drastically around different operating points, making combustion timing control difficult across a wide range of conditions. In this thesis, a graphical analysis examines the in-cylinder temperature dynamics of recompression HCCI and reveals three qualitative types of temperature dynamics. With this insight, a switching linear model is formulated by combining three linear models: one for each of the three types of temperature dynamics. A switching controller that is composed of three local linear feedback controllers can then be designed based on the switching model. This switching model/control formulation is tested on an experimental HCCI testbed and shows good performance in controlling the combustion timing across a wide range. A semi-definite program is formulated to find a Lyapunov function for the switching model/control framework and shows that it is stable. As HCCI is dictated by the in-cylinder thermo-chemical conditions, there are further concerns about the robustness of HCCI, i.e., the boundedness of the thermo-chemical conditions with uncertainty existing in the ambient conditions and in the engine's own characteristics due to aging. To assess HCCI's robustness, this thesis presents a linear parameter varying (LPV) model that captures the dynamics of recompression HCCI and possesses an elegant model structure that is more amenable to analysis. Based on this model, a recursive algorithm using convex optimization is formulated to generate analytical statements about the boundedness of the in-cylinder thermo-chemical conditions. The bounds generated by the algorithm are also shown to relate well to the data from the experimental testbed.
Author: Gautam Kalghatgi
Publisher: Springer Nature
ISBN: 9811687358
Category : Technology & Engineering
Languages : en
Pages : 339
Get Book Here
Book Description
This book focuses on gasoline compression ignition (GCI) which offers the prospect of engines with high efficiency and low exhaust emissions at a lower cost. A GCI engine is a compression ignition (CI) engine which is run on gasoline-like fuels (even on low-octane gasoline), making it significantly easier to control particulates and NOx but with high efficiency. The state of the art development to make GCI combustion feasible on practical vehicles is highlighted, e.g., on overcoming problems on cold start, high-pressure rise rates at high loads, transients, and HC and CO emissions. This book will be a useful guide to those in academia and industry.
Author:
Publisher:
ISBN:
Category : Internal combustion engines
Languages : en
Pages : 332
Get Book Here
Book Description
Author: Marwa Abdelgawad
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Homogeneous Charge Compression Ignition (HCCI) Engines hold promises of being the next generation of internal combustion engines due to their ability to produce high thermal efficiencies and low emission levels. HCCI combustion is achieved through the auto-ignition of a compressed homogenous fuel-air mixture, thus making it a "fusion" between spark-ignition and compression-ignition engines. The main challenge in developing HCCI engines is the absence of a combustion trigger hence making it difficult to control its combustion timing. The aim of this research project is to model and control a natural gas HCCI engine. Since HCCI depends primarily on temperature and chemical composition of the mixture, Exhaust Gas Recirculation (EGR) is used to control ignition timing. In this research, a thermodynamical, physics-based nonlinear model is developed to capture the main features of the HCCI engine. In addition, the Modified Knock Integral Model (MKIM), used to predict ignition timing, is optimized. To validate the nonlinear model, ignition timing under varying conditions using the MKIM approach is shown to be in accordance with data acquired from a model developed using a sophisticated engine simulation program, GT-Power. Most control strategies are based on a linear model, therefore, the nonlinear model is linearized using the perturbation method. The linear model is validated by comparing its performance with the nonlinear model about a suitable operating point. The control of ignition timing can be defined as a regulation process where the goal is to force the nonlinear model to track a desired ignition timing by controlling the EGR ratio. Parameters from the linear model are used to determine the gains of the LQR controller. The performance of the controller is validated by implementing it on the nonlinear model and observing its ability to track the desired timing with 0.5% error within a certain operating range. To increase the operating range of the controller and reduce steady-state error, an integrator is added to the LQR. Finally, it is shown that the LQR controller is able to successfully reject disturbance, parameter variation, as well as noise.
Author: William Lee Gans
Publisher:
ISBN:
Category :
Languages : en
Pages : 250
Get Book Here
Book Description
Author: Hua Zhao
Publisher: CRC Press
ISBN:
Category : Technology & Engineering
Languages : en
Pages : 562
Get Book Here
Book Description
Homogeneous charge compression ignition (HCCI)/controlled auto-ignition (CAI) has emerged as one of the most promising engine technologies with the potential to combine fuel efficiency and improved emissions performance, offering reduced nitrous oxides and particulate matter alongside efficiency comparable with modern diesel engines. Despite the considerable advantages, its operational range is rather limited and controlling the combustion (timing of ignition and rate of energy release) is still an area of on-going research. Commercial applications are, however, close to reality. HCCI a.
