Irradiation of U-Mo Base Alloys PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Irradiation of U-Mo Base Alloys PDF full book. Access full book title Irradiation of U-Mo Base Alloys by M. P. Johnson. Download full books in PDF and EPUB format.
Author: M. P. Johnson
Publisher:
ISBN:
Category : Molybdenum alloys
Languages : en
Pages : 38
Get Book Here
Book Description
A series of experiments was designed to assess the suitability of uranium-molybdenum alloys as high-temperature, high-burnup fuels for advanced sodium cooled reactors. Specimens with molybdenum contents between 3 and 10% were subjected to capsule irradiation tests in the Materials Testing Reactor, to burnups up to 10,000 Mwd/MTU at temperatures between 800 and 1500 deg F. The results indicated that molybdenum has a considerable effect in reducing the swelling due to irradiation. For example. 3% molybdemum reduces the swelling from 25%, for pure uranium. to 7% at approximates 3,000 Mwd/MTU at 1270 deg F. Further swelling resistance can be gained by increasing the molybdenum content, but the amount gained becomes successively smaller. At higher irradiation levels, the amount of swelling rapidly becomes greater, and larger amounts of molybdenum are required to provide similar resistance. A limit of 7% swelling, at 900 deg F and an irradiation of 7,230 Mwd/ MTU, requires the use of 10% Nonemolybdenum in the alloy. The burnup rates were in the range of 2.0 to 4.0 x 10p13s fissiom/cc-sec. Small ternary additions of silicon and aluminum were shown to have a noticeable effect in reducing swelling when added to a U-3% Mo alloy base. Under the conditions of the present experiment, 0.26% silicon or 0.38% aluminum were equivalent to 1 to 1 1/2% molybdenum. The Advanced Sodium Cooled Reactor requires a fuel capable of being irradiated to 20,000 Mwd/MTU at temperatures up to 1500 deg C in metal fuel, or equivalent in ceramic fuel. It is concluded that even the highest molybdenum contents considered did not produce a fuel capable of operating satisfactorily under these conditions. The alloys would be useful, however, for less exacting conditions. The U-3% Mo alloy is capable of use up to 3,000 Mwd/MTU at temperatures of 1300 deg F before swelling becomes excessive. The addition of silicon and aluminum would increase this limit to at least 3,000 Mwd/MTU, and possibly more if the
Author: M. P. Johnson
Publisher:
ISBN:
Category : Molybdenum alloys
Languages : en
Pages : 38
Get Book Here
Book Description
A series of experiments was designed to assess the suitability of uranium-molybdenum alloys as high-temperature, high-burnup fuels for advanced sodium cooled reactors. Specimens with molybdenum contents between 3 and 10% were subjected to capsule irradiation tests in the Materials Testing Reactor, to burnups up to 10,000 Mwd/MTU at temperatures between 800 and 1500 deg F. The results indicated that molybdenum has a considerable effect in reducing the swelling due to irradiation. For example. 3% molybdemum reduces the swelling from 25%, for pure uranium. to 7% at approximates 3,000 Mwd/MTU at 1270 deg F. Further swelling resistance can be gained by increasing the molybdenum content, but the amount gained becomes successively smaller. At higher irradiation levels, the amount of swelling rapidly becomes greater, and larger amounts of molybdenum are required to provide similar resistance. A limit of 7% swelling, at 900 deg F and an irradiation of 7,230 Mwd/ MTU, requires the use of 10% Nonemolybdenum in the alloy. The burnup rates were in the range of 2.0 to 4.0 x 10p13s fissiom/cc-sec. Small ternary additions of silicon and aluminum were shown to have a noticeable effect in reducing swelling when added to a U-3% Mo alloy base. Under the conditions of the present experiment, 0.26% silicon or 0.38% aluminum were equivalent to 1 to 1 1/2% molybdenum. The Advanced Sodium Cooled Reactor requires a fuel capable of being irradiated to 20,000 Mwd/MTU at temperatures up to 1500 deg C in metal fuel, or equivalent in ceramic fuel. It is concluded that even the highest molybdenum contents considered did not produce a fuel capable of operating satisfactorily under these conditions. The alloys would be useful, however, for less exacting conditions. The U-3% Mo alloy is capable of use up to 3,000 Mwd/MTU at temperatures of 1300 deg F before swelling becomes excessive. The addition of silicon and aluminum would increase this limit to at least 3,000 Mwd/MTU, and possibly more if the
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
A series of experiments was designed to assess the suitability of uranium-molybdenum alloys as high-temperature, high-burnup fuels for advanced sodium cooled reactors. Specimens with molybdenum contents between 3 and 10% were subjected to capsule irradiation tests in the Materials Testing Reactor, to burnups up to 10,000 Mwd/MTU at temperatures between 800 and 1500 deg F. The results indicated that molybdenum has a considerable effect in reducing the swelling due to irradiation. For example. 3% molybdemum reduces the swelling from 25%, for pure uranium. to 7% at approximates 3,000 Mwd/MTU at 1270 deg F. Further swelling resistance can be gained by increasing the molybdenum content, but the amount gained becomes successively smaller. At higher irradiation levels, the amount of swelling rapidly becomes greater, and larger amounts of molybdenum are required to provide similar resistance. A limit of 7% swelling, at 900 deg F and an irradiation of 7,230 Mwd/ MTU, requires the use of 10% Nonemolybdenum in the alloy. The burnup rates were in the range of 2.0 to 4.0 x 1013 fissiom/cc-sec. Small ternary additions of silicon and aluminum were shown to have a noticeable effect in reducing swelling when added to a U-3% Mo alloy base. Under the conditions of the present experiment, 0.26% silicon or 0.38% aluminum were equivalent to 1 to 1 1/2% molybdenum. The Advanced Sodium Cooled Reactor requires a fuel capable of being irradiated to 20,000 Mwd/MTU at temperatures up to 1500 deg C in metal fuel, or equivalent in ceramic fuel. It is concluded that even the highest molybdenum contents considered did not produce a fuel capable of operating satisfactorily under these conditions. The alloys would be useful, however, for less exacting conditions. The U-3% Mo alloy is capable of use up to 3,000 Mwd/MTU at temperatures of 1300 deg F before swelling becomes excessive. The addition of silicon and aluminum would increase this limit to at least 3,000 Mwd/MTU, and possibly more if the alloy were heat treated to provide a fine dispersion of second phase. (auth).
Author: Melvin L. Bleiberg
Publisher:
ISBN:
Category : Uranium alloys
Languages : en
Pages : 122
Get Book Here
Book Description
The effects of pile irradiations on the physical properties and corrosion resistance of U-- Mo, U-- Nb; and U--Si alloys are reported. The dimensional stability under irradiation of the gamma phase U-- Mo and U-- Nb alloys is excellent; however, an isotropic volume increase of 4 to 6% per wt.% burnup may limit the ultimate fuel element life. Corrosion resistance of the gamma-phase alloys appesrs to be improved when subjected to s neutron field; this is attributed to an irrsdiation induced stabilization of the gamma phases. The U/ sub 3/Si alloy, on the other hand, suffered severe deterioration, particularly of corrosion resistance. Changes in electrical resistivity, hardness, mechanical properties, and crystal structure are presented and the mechanisms producing the observed changes discussed.
Author: Jason L. Schulthess
Publisher:
ISBN: 9781085583084
Category : Uranium alloys
Languages : en
Pages : 174
Get Book Here
Book Description
Studies were conducted to establish the mechanical properties of uranium 10 wt.% molybdenum (U-10Mo) in both the un-irradiated condition and after neutron irradiation. In the un-irradiated condition, mechanical properties were obtained for various temperatures and after the alloy had been wrought processed by rolling into four different rolling conditions. The irradiated mechanical properties were obtained at various fission densities and then the degradation of the mechanical properties from the un-irradiated to irradiated condition evaluated and a correlation with porosity developed. The mechanical properties obtained of the un-irradiated material differed from that previously published in the literature, which was expected due to the differences in thermomechanical processing conditions between the materials evaluated. The mechanical properties degraded as fission density increased as expected, and correlate to the increase of porosity that develops with increasing fission density.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Based on data available in 2009, a decision was ma.
Author: I. Cohen
Publisher:
ISBN:
Category : Uranium alloys
Languages : en
Pages : 322
Get Book Here
Book Description
The effects of pile irradiations on the physical properties and corrosion resistance of U-- Mo, U-- Nb; and U--Si alloys are reported. The dimensional stability under irradiation of the gamma phase U-- Mo and U-- Nb alloys is excellent; however, an isotropic volume increase of 4 to 6% per wt.% burnup may limit the ultimate fuel element life. Corrosion resistance of the gamma-phase alloys appesrs to be improved when subjected to s neutron field; this is attributed to an irrsdiation induced stabilization of the gamma phases. The U/ sub 3/Si alloy, on the other hand, suffered severe deterioration, particularly of corrosion resistance. Changes in electrical resistivity, hardness, mechanical properties, and crystal structure are presented and the mechanisms producing the observed changes discussed.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
A down-selection process has been applied to the U-Mo fuel alloy based monolithic plate fuel design, supported by irradiation testing of small fuel plates containing various design parameters. The irradiation testing provided data on fuel performance issues such as swelling, fuel-cladding interaction (interdiffusion), blister formation at elevated temperatures, and fuel/cladding bond quality and effectiveness. U-10Mo (wt%) was selected as the fuel alloy of choice, accepting a somewhat lower uranium density for the benefits of phase stability. U-7Mo could be used, with a barrier, where the trade-off for uranium density is critical to nuclear performance. A zirconium foil barrier between fuel and cladding was chosen to provide a predictable, well-bonded, fuel-cladding interface, allowing little or no fuel-cladding interaction. The fuel plate testing conducted to inform this selection was based on the use of U-10Mo foils fabricated by hot co-rolling with a Zr foil. The foils were subsequently bonded to Al-6061 cladding by hot isostatic pressing or friction stir bonding.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Irradiation results in the range near 1/2% burnup and 500 to 600 deg C are presented for U-fissium amd U-Mo alloys. Under these conditions both classes of alloys show quite low growth coefficients and volume increases, with a few exceptions. Water queaching either alloy from 850 deg C is shown to be unsatisfactory. The effect of an axial hole for relief of fission gases appears to be inconclusive. Surface condition of irradiated U-base alloys appears to be not quite as good as that for U-20 wt.% Pu base alloys. (auth).
Author: National Research Council
Publisher: National Academies Press
ISBN: 0309130395
Category : Medical
Languages : en
Pages : 220
Get Book Here
Book Description
This book is the product of a congressionally mandated study to examine the feasibility of eliminating the use of highly enriched uranium (HEU2) in reactor fuel, reactor targets, and medical isotope production facilities. The book focuses primarily on the use of HEU for the production of the medical isotope molybdenum-99 (Mo-99), whose decay product, technetium-99m3 (Tc-99m), is used in the majority of medical diagnostic imaging procedures in the United States, and secondarily on the use of HEU for research and test reactor fuel. The supply of Mo-99 in the U.S. is likely to be unreliable until newer production sources come online. The reliability of the current supply system is an important medical isotope concern; this book concludes that achieving a cost difference of less than 10 percent in facilities that will need to convert from HEU- to LEU-based Mo-99 production is much less important than is reliability of supply.
Author: International Atomic Energy Agency
Publisher:
ISBN: 9789201157201
Category : Technology & Engineering
Languages : en
Pages : 144
Get Book Here
Book Description
This publication presents the material properties of all unirradiated Uranium-Molybdenum (U-Mo) fuel constituents that are essential for fuel designers and reactor operators to evaluate the fuel's performance and safety for research reactors. Many significant advances in the understanding and development of low enriched uranium U-Mo fuels have been made since 2004, stimulated by the need to understand irradiation behavior and early fuel failures during testing. The publication presents a comprehensive overview of mechanical and physical property data from U-Mo fuel research
