Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 1: Threaded Port with O-Ring Seal in Truncated Housing

Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 1: Threaded Port with O-Ring Seal in Truncated Housing PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J1926 specifies dimensions for fluid power and general use ports with inch threads in accordance with ASME B1.1 for use with adjustable and nonadjustable stud ends and plugs shown in SAE J1926-2, SAE J1926-3, and SAE J1926-4.Ports in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new designs in hydraulic fluid power applications. Five-Year Review.

Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 1: Threaded Port with O-Ring Seal in Truncated Housing

Connections for General Use and Fluid Power - Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 1: Threaded Port with O-Ring Seal in Truncated Housing PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J1926 specifies dimensions for fluid power and general use ports with inch threads in accordance with ASME B1.1 for use with adjustable and nonadjustable stud ends and plugs shown in SAE J1926-2, SAE J1926-3, and SAE J1926-4.Ports in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new designs in hydraulic fluid power applications. Five-Year Review.

Connections for General Use and Fluid PowerPorts and Stud Ends with ASME B1.1 Threads and O-Ring SealingPart 1: Threaded Port with O-Ring Seal in Truncated Housing

Connections for General Use and Fluid PowerPorts and Stud Ends with ASME B1.1 Threads and O-Ring SealingPart 1: Threaded Port with O-Ring Seal in Truncated Housing PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J1926 specifies dimensions for fluid power and general use ports with inch threads in accordance with ASME B1.1 for use with adjustable and nonadjustable stud ends shown in SAE J1926-2 and SAE J1926-3.Ports in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new designs in hydraulic fluid power applications. To add sizes 40, 48 and 64 and make general editorial corrections.

Connections for General Use and Fluid Power-Ports and Stud Ends With Iso 725 Threads and O-Ring Sealing-Part 1: Threaded Port With O-Ring Seal in Truncated Housing

Connections for General Use and Fluid Power-Ports and Stud Ends With Iso 725 Threads and O-Ring Sealing-Part 1: Threaded Port With O-Ring Seal in Truncated Housing PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J1926 specifies dimensions for fluid power and general use ports with inch threads to ISO 725 for use with adjustable and nonadjustable stud ends shown in SAE J1926-2 and SAE J1926-3. Ports in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends up to 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.

Connections for General Use and Fluid Power Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 2: Heavy-Duty (S Series) Stud Ends

Connections for General Use and Fluid Power Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing - Part 2: Heavy-Duty (S Series) Stud Ends PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ASME B1.1 threads for use in fluid power and general applications.Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 41.3 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications. Conformance to the dimensional information does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance rating.Appendices A and B of this document are informative. This document was revised in order to remove Table 5.

Connections for Fluid Power and General Use-Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing Part 1: Port With O-Ring Seal in Truncated Housing

Connections for Fluid Power and General Use-Ports and Stud Ends With Iso 261 Threads and O-Ring Sealing Part 1: Port With O-Ring Seal in Truncated Housing PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J2244 specifies dimensions for fluid powermetric ports for use with adjustable and nonadjustable stud endsshown in SAE J2244/2.Ports in accordance with this part of SAE J2244 may be used atworking pressures up to 63 MPa for nonadjustable stud ends and 40MPa for adjustable stud ends. The permissible working pressuredepends upon materials, design, working conditions, application,etc.For threaded ports and stud ends specified in new designs inhydraulic fluid power applications, only SAE J2244 shall be used.Threaded ports and stud ends in accordance with ISO 1179, ISO 9974,and SAE J1926 (ISO 11926) shall not be used for new designs inhydraulic fluid power applications.

Connections for General Use and Fluid Power Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing Part 3: Light-Duty (L-Series) Stud Ends

Connections for General Use and Fluid Power Ports and Stud Ends with ASME B1.1 Threads and O-Ring Sealing Part 3: Light-Duty (L-Series) Stud Ends PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable light-duty (L series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them.Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 35 MPa for nonadjustable and adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud end specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications.Conformance to the dimensional information does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance rating.Appendices A and B of this document are informative. This document was revised in order to remove Table 5.

Connections for Fluid Power and General UsePorts and Stud Ends with ISO 261 Threads and O-Ring Sealing Part 1: Port with O-Ring Seal in Truncated Housing

Connections for Fluid Power and General UsePorts and Stud Ends with ISO 261 Threads and O-Ring Sealing Part 1: Port with O-Ring Seal in Truncated Housing PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J2244 specifies dimensions for fluid power metric ports for use with adjustable and nonadjustable stud ends shown in SAE J2244/2.Ports in accordance with this part of SAE J2244 may be used at working pressures up to 63 MPa for nonadjustable stud ends and 40 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs in hydraulic fluid power applications, only SAE J2244 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and SAE J1926 (ISO 11926) shall not be used for new designs in hydraulic fluid power applications. All parts of SAE J2244 are being cancelled. SAE J2244 was published to provide users and manufacturers access to metric port and stud end dimensions. ISO 6149 is more recognized in the industry as the preferred metric port and stud end standard, thus the SAE FCCTC SC1 committee has approved cancelling SAE J2244-1 and superseding it with ISO 6149-1.

Connections for General Use and Fluid PowerPorts and Stud Ends with ASME B1.1 Threads and O-Ring SealingPart 3: Light-Duty (L-Series) Stud Ends

Connections for General Use and Fluid PowerPorts and Stud Ends with ASME B1.1 Threads and O-Ring SealingPart 3: Light-Duty (L-Series) Stud Ends PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable light-duty (L series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them.Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 35 MPa for nonadjustable and adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud end specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications.Conformance to the dimensional Information does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance rating.Appendices A of this document is informative.NOTE: This document specifies inch as well as metric hexes for the stud ends. Therefore, any product drawing specifying stud ends in accordance with this document must specify hex type, inch or metric, to assure getting intended hex.Stud ends or parts specified before January 1, 2010 using this standard, shall be supplied with inch hexes, unless otherwise specified. General revision for harmonizationwith SAE J514 and ISO 11926-3 and addition of sizes -40, -48 and -64 and converting the document to metric hex standard in accordance with FCCTC resolution on metric hex conversion. The resolution provides rationale for converting to metric hex and not using inch hex for new designs as follows: "In an effort to standardize within a global market and ensuring that companies can remain competitive in an international market, it is the intent to convert to metric hex sizes which will: -lead to one global standard -guide users to a preferred system -reduce complexity -eliminate duplication -reduce confusion"

Connections for General Use and Fluid PowerPorts and Stud Ends with ASME B1.1 Threads and O-Ring SealingPart 2: Heavy-Duty (S Series) Stud Ends

Connections for General Use and Fluid PowerPorts and Stud Ends with ASME B1.1 Threads and O-Ring SealingPart 2: Heavy-Duty (S Series) Stud Ends PDF Author: Hydraulic Tube Fittings Committee
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
This part of SAE J1926 specifies dimensions, performance requirements, and test procedures for adjustable and nonadjustable heavy-duty (S series) stud ends with ASME B1.1 threads for use in fluid power and general applications and the O-rings used with them that are currently not listed in SAE J515.Stud ends in accordance with this part of SAE J1926 may be used at working pressures up to 63 MPa for nonadjustable stud ends and up to 41.3 MPa for adjustable stud ends. The permissible working pressure depends upon materials, design, working conditions, application, etc.For threaded ports and stud ends specified in new designs for hydraulic fluid power applications, only ISO 6149 shall be used. Threaded ports and stud ends in accordance with ISO 1179, ISO 9974, and ISO 11926 shall not be used for new design in hydraulic fluid power applications.NOTE: This document specifies inch as well as metric hexes for the stud ends. Therefore, any product drawing specifying stud ends in accordance with this document must specify hex type, inch or metric, to assure getting intended hex.Stud ends or parts specified before January 1, 2010 using this standard, shall be supplied with inch hexes, unless otherwise specified.Conformance to the dimensional information does not guarantee rated performance. Each manufacturer shall perform testing according to the specification contained in this document to ensure that components made to this document comply with the performance rating.Appendix A of this document is informative. General revision for harmonization with J1453-3 and ISO 11926-2, addition of sizes -32, -40 and-48 and converting the document to metric hex standard in accordance with FCCTC resolution on metric hex conversion. The resolution provides rationale for converting to metric hex and not using inch hex for new designs as follows: "In an effort to standardize within a global market and ensuring that companies can remain competitive in an international market, it is the intent to convert to metric hex sizes which will: -lead to one global standard -guide users to a preferred system -reduce complexity -eliminate duplication -reduce confusion"

Connections for hydraulic fluid power and general use - ports and stud ends with ISO 261 metric threads and O-ring sealing - part 1 : ports with truncated housing for O-ring seal

Connections for hydraulic fluid power and general use - ports and stud ends with ISO 261 metric threads and O-ring sealing - part 1 : ports with truncated housing for O-ring seal PDF Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description