U.S. Government Research Reports PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download U.S. Government Research Reports PDF full book. Access full book title U.S. Government Research Reports by . Download full books in PDF and EPUB format.
Author:
Publisher:
ISBN:
Category : Science
Languages : en
Pages : 106
Get Book Here
Book Description
Author:
Publisher:
ISBN:
Category : Science
Languages : en
Pages : 106
Get Book Here
Book Description
Author:
Publisher:
ISBN:
Category : Nuclear reactors
Languages : en
Pages : 602
Get Book Here
Book Description
Author: D. J. Maykuth
Publisher:
ISBN:
Category : Heat resistant alloys
Languages : en
Pages : 48
Get Book Here
Book Description
This report is the third of a series which will periodically summarize the status of the various contracts involved in the Department of Defense Refractory Metals Sheet Rolling Program. Under this program, selected candidate materials are being carried through one or more of the following consecutive phases: Phase I, development of a sheet-production practice; Phase II, establishment of minimum design data; and Phase III, evaluation of sheetfabrication characteristics. To the present time, 13 contracts have been funded or planned in support of the Phase I, II, and III activities. This report summarizes the status of each of these individual contracts as of November 1, 1964. The first section describes the overall program of the Department of Defense Refractory Metals Sheet Rolling Program. Following, in the order of their discussions, are sections dealing with fabricable molybdenum alloys, unalloyed tungsten, columbium alloys, and tantalum alloys. (Author).
Author: Erik Lassner
Publisher: Springer Science & Business Media
ISBN: 1461549078
Category : Science
Languages : en
Pages : 432
Get Book Here
Book Description
Why does someone write a book about Tungsten? There are several reasons and precedents for this, the most important of which is that the last book on tungsten was written more than 20 years ago, in 1977, by St. W H. Yih and Ch T. Wang. During the intervening period there have been many new scientific and technological developments and innova tions, so it was not only our opinion but the view of many other members of the "tungsten family" that it was time to start writing a new book about tungsten. Preparations of the new book began in 1994. further impetus to the project was provided by the realization that in spite of this new knowledge having been presented at seminars or published in the technical press, a general acknowledgement of it by the majority of technicians and scientists is still far from being realized. It is our hope that this book will significantly contribute to a broader acceptance of recent scientific and technological innovations. An important prerequisite for such a project is the availability of a recently retired, experienced person willing to devote his time and talents to the tedious part of the exercise.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 54
Get Book Here
Book Description
To aid in quick identification and easy location of specific technical data and information in the various reports and memoranda which have been prepared and distributed by the Defense Metals Information Center, as well as by DMIC's forerunner, the Titanium Metallurgical Laboratory, a classification by major subject matter was prepared. The classification covers reports through DMIC Report 193 and memoranda through DMIC Memorandum 183. (Author).
Author: F. C. Holden
Publisher:
ISBN:
Category : Alloys
Languages : en
Pages : 102
Get Book Here
Book Description
A summary is given of the status of the various contracts involved in the U.S. Government's Metalworking Processes and Equipment Program. (Author).
Author: Albert M. Hall
Publisher:
ISBN:
Category : Nickel
Languages : en
Pages : 34
Get Book Here
Book Description
Various aspects of the physical metallurgy of the 18 % nickel maraging steels are discussed in this report in the light of the knowledge which has thus far been accumulated on these steels. The 18 % nickel type of maraging steel was singled out for discussion because of its especially attractive combination of strength and fracture toughness, the comparative simplicity with which it can be hardened, and the relative ease with which it can be formed and joined. The highnickel maraging steels are considered to be outstanding members of a loose-knit family of agehardenable or precipitation-hardenable martensitic steels. Some comparisons and analogies are drawn among various members of this family with particular reference to the 18% nickel steels. (Author).
Author: Robert Melvin Evans
Publisher:
ISBN:
Category : Nickel alloys
Languages : en
Pages : 30
Get Book Here
Book Description
Because of a special interest in Alloy 718, the Defense Metals Information Center has summarized information on the welding and brazing of the alloy. Two principal resons for the interest in this alloy are its good formability and its good weldability, expecially under restraint. The greater portion of the fusion welding of Alloy 718 has been done by the gas tungsten-arc (TIG) process. A discussion of welding atmosphere, filler metals, heat treatment of welds, welding under restraint, and weld toughness is presented in the section on fusion welding. Information is also presented on resistance welding and electron-beam welding of Alloy 718. The final section of this report deals with the brazing of Alloy 718.
Author: John A. Gurklis
Publisher:
ISBN:
Category : Chemical milling
Languages : en
Pages : 52
Get Book Here
Book Description
This report assembles and correlates information on the effects of electrochemical metal-removal (ECMR) processes on mechanical properties. Of special interest and concern are the effects of ECMR on fatigue strength. The report covers four electrochemical metal-removal processes: electrochemical machining (ECM), electrolytic grinding (EG), electrochemical milling, and electropolishing. General characteristics and applications of the four methods are presented and discussed; special emphasis is placed on ECM. The ECMR processes are especially useful in shaping high-strength and difficult-to-machine metals and alloys, as well as in shaping parts with unusual, complex, or fragile characteristics. (Author).
Author: J. E. Campbell
Publisher:
ISBN:
Category : Alloys
Languages : en
Pages : 32
Get Book Here
Book Description
Fracture-toughness testing using principles of fracture mechanics has developed to the point where it can be used as a basis for selection of materials, for estimating limiting design stresses assuming the presence of small flaws, and for analyzing failures. Current methods of measuring plane-stress and plane-strain fracturetoughness parameters are presented in this report. The specimens include center-cracked, edge-cracked, single-edge-cracked, surface-cracked, and notched round bars, which are subjected to tensile loading, and notched bars for bend tests. The different types of specimens permit evaluating sheet, plate, bar stock, and forgings as well as material from failed structures. Application of fracture-toughness parameters to design of high-strength structures is reviewed for both static and fatigue loading. Consideration of the fracture-mechanics concepts in design should lead to fewer problems with brittle fracture in high-strength structures. (Author).
