Technical Notes on Next Generation Aero Combustor Design-Development and Related Combustion Research PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Technical Notes on Next Generation Aero Combustor Design-Development and Related Combustion Research PDF full book. Access full book title Technical Notes on Next Generation Aero Combustor Design-Development and Related Combustion Research by Jushan Chin. Download full books in PDF and EPUB format.
Author: Jushan Chin
Publisher: Nova Science Publishers
ISBN: 9781685071097
Category : Technology & Engineering
Languages : en
Pages : 165
Get Book Here
Book Description
"The aim of this book is to identify that extra high-pressure ratio (such as about 70) civil aero engine low emissions combustors and extra high fuel air ratio (FAR) (such as FAR greater than 0.051) military aero engine combustors make up the next generation of aero combustors. The aero thermal design of these combustors is very different from previous combustors and the major design points are proposed. Two types of high-pressure low emissions combustor design have been suggested: one is without fuel staging and the other is with fuel staging. The high FAR combustor design is brand new. The layout of the next-generation aero combustor is very different. There are no primary holes, no intermediate holes, and no dilution holes. They all have direct mixing combustion. For low-emissions combustors, it is lean direct mixing (LDM) combustion. For high-FAR combustors, it is stoichiometric direct mixing combustion. Combustion air fraction is very high (such as greater than 75%). That will induce idle condition lean blow out (LBO) issue. The present book has proposed several design approaches to solve idle LBO issue, which are effective. Pilot fuel air combustion is designed at idle condition. For civil combustor, maximum condition is designed for low emissions, while for high FAR combustor, maximum condition is designed for non-visible smoke, low luminous flame radiation and good combustion efficiency. For each type of combustor, the fuel air module configuration is designed, which is the most essential part of combustor design. The brand-new combustor cooling design has used a compound angle tangential inlet cooling hole configuration. Such a cooling design provides high cooling effectiveness. The diffuser configuration is totally new. It is an air bleeding diffuser, directly stretching forward to contact the dome. The bled air flows to the annular channel as cooling air. Aero combustor development is discussed in this book. In particular, the combustor developments from technology readiness level (TRL) 3 to TRL level 6 have been discussed in detail. Also reported is the technology to run combustor development tests correctly. Three topics of related combustion research by the present author are summarized in the brochure. They are: a. Fuel injection and co-flowing air combination. The key point is, for next generation combustor development, the designer should not only think about atomization. The combination of fuel injection and co-flowing air should be considered together as a whole device. b. Fuel spray evaporation calculation, the key is an engineering calculation of multi-component fuel evaporation shall be used. c. Non-luminous flame radiation calculation, which has been significantly updated. The present book is a summary of the author's ten years of study on next-generation aero combustors after retirement. It represents advanced aero combustor technology level"--
Author: Jushan Chin
Publisher: Nova Science Publishers
ISBN: 9781685071097
Category : Technology & Engineering
Languages : en
Pages : 165
Get Book Here
Book Description
"The aim of this book is to identify that extra high-pressure ratio (such as about 70) civil aero engine low emissions combustors and extra high fuel air ratio (FAR) (such as FAR greater than 0.051) military aero engine combustors make up the next generation of aero combustors. The aero thermal design of these combustors is very different from previous combustors and the major design points are proposed. Two types of high-pressure low emissions combustor design have been suggested: one is without fuel staging and the other is with fuel staging. The high FAR combustor design is brand new. The layout of the next-generation aero combustor is very different. There are no primary holes, no intermediate holes, and no dilution holes. They all have direct mixing combustion. For low-emissions combustors, it is lean direct mixing (LDM) combustion. For high-FAR combustors, it is stoichiometric direct mixing combustion. Combustion air fraction is very high (such as greater than 75%). That will induce idle condition lean blow out (LBO) issue. The present book has proposed several design approaches to solve idle LBO issue, which are effective. Pilot fuel air combustion is designed at idle condition. For civil combustor, maximum condition is designed for low emissions, while for high FAR combustor, maximum condition is designed for non-visible smoke, low luminous flame radiation and good combustion efficiency. For each type of combustor, the fuel air module configuration is designed, which is the most essential part of combustor design. The brand-new combustor cooling design has used a compound angle tangential inlet cooling hole configuration. Such a cooling design provides high cooling effectiveness. The diffuser configuration is totally new. It is an air bleeding diffuser, directly stretching forward to contact the dome. The bled air flows to the annular channel as cooling air. Aero combustor development is discussed in this book. In particular, the combustor developments from technology readiness level (TRL) 3 to TRL level 6 have been discussed in detail. Also reported is the technology to run combustor development tests correctly. Three topics of related combustion research by the present author are summarized in the brochure. They are: a. Fuel injection and co-flowing air combination. The key point is, for next generation combustor development, the designer should not only think about atomization. The combination of fuel injection and co-flowing air should be considered together as a whole device. b. Fuel spray evaporation calculation, the key is an engineering calculation of multi-component fuel evaporation shall be used. c. Non-luminous flame radiation calculation, which has been significantly updated. The present book is a summary of the author's ten years of study on next-generation aero combustors after retirement. It represents advanced aero combustor technology level"--
Author: Jushan Chin
Publisher: Nova Science Publishers
ISBN: 9781536197242
Category : Aircraft gas-turbines
Languages : en
Pages : 0
Get Book Here
Book Description
"The aim of this book is to identify that extra high-pressure ratio (such as about 70) civil aero engine low emissions combustors and extra high fuel air ratio (FAR) (such as FAR greater than 0.051) military aero engine combustors make up the next generation of aero combustors. The aero thermal design of these combustors is very different from previous combustors and the major design points are proposed. Two types of high-pressure low emissions combustor design have been suggested: one is without fuel staging and the other is with fuel staging. The high FAR combustor design is brand new. The layout of the next-generation aero combustor is very different. There are no primary holes, no intermediate holes, and no dilution holes. They all have direct mixing combustion. For low-emissions combustors, it is lean direct mixing (LDM) combustion. For high-FAR combustors, it is stoichiometric direct mixing combustion. Combustion air fraction is very high (such as greater than 75%). That will induce idle condition lean blow out (LBO) issue. The present book has proposed several design approaches to solve idle LBO issue, which are effective. Pilot fuel air combustion is designed at idle condition. For civil combustor, maximum condition is designed for low emissions, while for high FAR combustor, maximum condition is designed for non-visible smoke, low luminous flame radiation and good combustion efficiency. For each type of combustor, the fuel air module configuration is designed, which is the most essential part of combustor design. The brand-new combustor cooling design has used a compound angle tangential inlet cooling hole configuration. Such a cooling design provides high cooling effectiveness. The diffuser configuration is totally new. It is an air bleeding diffuser, directly stretching forward to contact the dome. The bled air flows to the annular channel as cooling air. Aero combustor development is discussed in this book. In particular, the combustor developments from technology readiness level (TRL) 3 to TRL level 6 have been discussed in detail. Also reported is the technology to run combustor development tests correctly. Three topics of related combustion research by the present author are summarized in the brochure. They are: a. Fuel injection and co-flowing air combination. The key point is, for next generation combustor development, the designer should not only think about atomization. The combination of fuel injection and co-flowing air should be considered together as a whole device. b. Fuel spray evaporation calculation, the key is an engineering calculation of multi-component fuel evaporation shall be used. c. Non-luminous flame radiation calculation, which has been significantly updated. The present book is a summary of the author's ten years of study on next-generation aero combustors after retirement. It represents advanced aero combustor technology level"--
Author: Tolga Taner
Publisher: BoD – Books on Demand
ISBN: 1838810005
Category :
Languages : en
Pages : 430
Get Book Here
Book Description
This book discusses renewable energy resources and systems as well as energy efficiency. It contains twenty-three chapters over six sections that address a multitude of renewable energy types, including solar and photovoltaic, biomass, hydroelectric, and geothermal. The information presented herein is a scientific contribution to energy and environmental regulations, quality and efficiency of energy services, energy supply security, energy market-based approaches, government interventions, and the spread of technological innovation.
Author: Anna Schwarz
Publisher: Springer Science & Business Media
ISBN: 3642020380
Category : Technology & Engineering
Languages : en
Pages : 304
Get Book Here
Book Description
November, 2008 Anna Schwarz, Johannes Janicka In the last thirty years noise emission has developed into a topic of increasing importance to society and economy. In ?elds such as air, road and rail traf?c, the control of noise emissions and development of associated noise-reduction techno- gies is a central requirement for social acceptance and economical competitiveness. The noise emission of combustion systems is a major part of the task of noise - duction. The following aspects motivate research: • Modern combustion chambers in technical combustion systems with low pol- tion exhausts are 5 - 8 dB louder compared to their predecessors. In the ope- tional state the noise pressure levels achieved can even be 10-15 dB louder. • High capacity torches in the chemical industry are usually placed at ground level because of the reasons of noise emissions instead of being placed at a height suitable for safety and security. • For airplanes the combustion emissions become a more and more important topic. The combustion instability and noise issues are one major obstacle for the introduction of green technologies as lean fuel combustion and premixed burners in aero-engines. The direct and indirect contribution of combustion noise to the overall core noise is still under discussion. However, it is clear that the core noise besides the fan tone will become an important noise source in future aero-engine designs. To further reduce the jet noise, geared ultra high bypass ratio fans are driven by only a few highly loaded turbine stages.
Author: S. Can Gülen
Publisher: Cambridge University Press
ISBN: 1108416659
Category : Business & Economics
Languages : en
Pages : 735
Get Book Here
Book Description
Everything you wanted to know about industrial gas turbines for electric power generation in one source with hard-to-find, hands-on technical information.
Author: Meherwan P. Boyce
Publisher: Elsevier
ISBN: 0080456898
Category : Mathematics
Languages : en
Pages : 956
Get Book Here
Book Description
The Gas Turbine Engineering Handbook has been the standard for engineers involved in the design, selection, and operation of gas turbines. This revision includes new case histories, the latest techniques, and new designs to comply with recently passed legislation. By keeping the book up to date with new, emerging topics, Boyce ensures that this book will remain the standard and most widely used book in this field. The new Third Edition of the Gas Turbine Engineering Hand Book updates the book to cover the new generation of Advanced gas Turbines. It examines the benefit and some of the major problems that have been encountered by these new turbines. The book keeps abreast of the environmental changes and the industries answer to these new regulations. A new chapter on case histories has been added to enable the engineer in the field to keep abreast of problems that are being encountered and the solutions that have resulted in solving them. - Comprehensive treatment of Gas Turbines from Design to Operation and Maintenance. In depth treatment of Compressors with emphasis on surge, rotating stall, and choke; Combustors with emphasis on Dry Low NOx Combustors; and Turbines with emphasis on Metallurgy and new cooling schemes. An excellent introductory book for the student and field engineers - A special maintenance section dealing with the advanced gas turbines, and special diagnostic charts have been provided that will enable the reader to troubleshoot problems he encounters in the field - The third edition consists of many Case Histories of Gas Turbine problems. This should enable the field engineer to avoid some of these same generic problems
Author: Arthur H. Lefebvre
Publisher: CRC Press
ISBN: 1420086057
Category : Science
Languages : en
Pages : 560
Get Book Here
Book Description
Reflecting the developments in gas turbine combustion technology that have occurred in the last decade, Gas Turbine Combustion: Alternative Fuels and Emissions, Third Edition provides an up-to-date design manual and research reference on the design, manufacture, and operation of gas turbine combustors in applications ranging from aeronautical to po
Author: National Academies of Sciences, Engineering, and Medicine
Publisher: National Academies Press
ISBN: 0309440998
Category : Technology & Engineering
Languages : en
Pages : 123
Get Book Here
Book Description
The primary human activities that release carbon dioxide (CO2) into the atmosphere are the combustion of fossil fuels (coal, natural gas, and oil) to generate electricity, the provision of energy for transportation, and as a consequence of some industrial processes. Although aviation CO2 emissions only make up approximately 2.0 to 2.5 percent of total global annual CO2 emissions, research to reduce CO2 emissions is urgent because (1) such reductions may be legislated even as commercial air travel grows, (2) because it takes new technology a long time to propagate into and through the aviation fleet, and (3) because of the ongoing impact of global CO2 emissions. Commercial Aircraft Propulsion and Energy Systems Research develops a national research agenda for reducing CO2 emissions from commercial aviation. This report focuses on propulsion and energy technologies for reducing carbon emissions from large, commercial aircraftâ€" single-aisle and twin-aisle aircraft that carry 100 or more passengersâ€"because such aircraft account for more than 90 percent of global emissions from commercial aircraft. Moreover, while smaller aircraft also emit CO2, they make only a minor contribution to global emissions, and many technologies that reduce CO2 emissions for large aircraft also apply to smaller aircraft. As commercial aviation continues to grow in terms of revenue-passenger miles and cargo ton miles, CO2 emissions are expected to increase. To reduce the contribution of aviation to climate change, it is essential to improve the effectiveness of ongoing efforts to reduce emissions and initiate research into new approaches.
Author: National Research Council
Publisher: National Academies Press
ISBN: 0309102472
Category : Technology & Engineering
Languages : en
Pages : 288
Get Book Here
Book Description
Rocket and air-breathing propulsion systems are the foundation on which planning for future aerospace systems rests. A Review of United States Air Force and Department of Defense Aerospace Propulsion Needs assesses the existing technical base in these areas and examines the future Air Force capabilities the base will be expected to support. This report also defines gaps and recommends where future warfighter capabilities not yet fully defined could be met by current science and technology development plans.
Author: Timothy C. Lieuwen
Publisher: AIAA (American Institute of Aeronautics & Astronautics)
ISBN:
Category : Science
Languages : en
Pages : 688
Get Book Here
Book Description
This book offers gas turbine users and manufacturers a valuable resource to help them sort through issues associated with combustion instabilities. In the last ten years, substantial efforts have been made in the industrial, governmental, and academic communities to understand the unique issues associated with combustion instabilities in low-emission gas turbines. The objective of this book is to compile these results into a series of chapters that address the various facets of the problem. The Case Studies section speaks to specific manufacturer and user experiences with combustion instabilities in the development stage and in fielded turbine engines. The book then goes on to examine The Fundamental Mechanisms, The Combustor Modeling, and Control Approaches.
