Modeling Engine Spray and Combustion Processes PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Modeling Engine Spray and Combustion Processes PDF full book. Access full book title Modeling Engine Spray and Combustion Processes by Gunnar Stiesch. Download full books in PDF and EPUB format.
Author: Gunnar Stiesch
Publisher: Springer Science & Business Media
ISBN: 3662087901
Category : Computers
Languages : en
Pages : 293
Get Book Here
Book Description
The utilization of mathematical models to numerically describe the performance of internal combustion engines is of great significance in the development of new and improved engines. Today, such simulation models can already be viewed as standard tools, and their importance is likely to increase further as available com puter power is expected to increase and the predictive quality of the models is constantly enhanced. This book describes and discusses the most widely used mathematical models for in-cylinder spray and combustion processes, which are the most important subprocesses affecting engine fuel consumption and pollutant emissions. The relevant thermodynamic, fluid dynamic and chemical principles are summarized, and then the application of these principles to the in-cylinder processes is ex plained. Different modeling approaches for the each subprocesses are compared and discussed with respect to the governing model assumptions and simplifica tions. Conclusions are drawn as to which model approach is appropriate for a specific type of problem in the development process of an engine. Hence, this book may serve both as a graduate level textbook for combustion engineering stu dents and as a reference for professionals employed in the field of combustion en gine modeling. The research necessary for this book was carried out during my employment as a postdoctoral scientist at the Institute of Technical Combustion (ITV) at the Uni versity of Hannover, Germany and at the Engine Research Center (ERC) at the University of Wisconsin-Madison, USA.
Author: Gunnar Stiesch
Publisher: Springer Science & Business Media
ISBN: 3662087901
Category : Computers
Languages : en
Pages : 293
Get Book Here
Book Description
The utilization of mathematical models to numerically describe the performance of internal combustion engines is of great significance in the development of new and improved engines. Today, such simulation models can already be viewed as standard tools, and their importance is likely to increase further as available com puter power is expected to increase and the predictive quality of the models is constantly enhanced. This book describes and discusses the most widely used mathematical models for in-cylinder spray and combustion processes, which are the most important subprocesses affecting engine fuel consumption and pollutant emissions. The relevant thermodynamic, fluid dynamic and chemical principles are summarized, and then the application of these principles to the in-cylinder processes is ex plained. Different modeling approaches for the each subprocesses are compared and discussed with respect to the governing model assumptions and simplifica tions. Conclusions are drawn as to which model approach is appropriate for a specific type of problem in the development process of an engine. Hence, this book may serve both as a graduate level textbook for combustion engineering stu dents and as a reference for professionals employed in the field of combustion en gine modeling. The research necessary for this book was carried out during my employment as a postdoctoral scientist at the Institute of Technical Combustion (ITV) at the Uni versity of Hannover, Germany and at the Engine Research Center (ERC) at the University of Wisconsin-Madison, USA.
Author: Carsten Baumgarten
Publisher: Springer Science & Business Media
ISBN: 3540308369
Category : Technology & Engineering
Languages : en
Pages : 312
Get Book Here
Book Description
A systematic control of mixture formation with modern high-pressure injection systems enables us to achieve considerable improvements of the combustion pr- ess in terms of reduced fuel consumption and engine-out raw emissions. However, because of the growing number of free parameters due to more flexible injection systems, variable valve trains, the application of different combustion concepts within different regions of the engine map, etc., the prediction of spray and m- ture formation becomes increasingly complex. For this reason, the optimization of the in-cylinder processes using 3D computational fluid dynamics (CFD) becomes increasingly important. In these CFD codes, the detailed modeling of spray and mixture formation is a prerequisite for the correct calculation of the subsequent processes like ignition, combustion and formation of emissions. Although such simulation tools can be viewed as standard tools today, the predictive quality of the sub-models is c- stantly enhanced by a more accurate and detailed modeling of the relevant pr- esses, and by the inclusion of new important mechanisms and effects that come along with the development of new injection systems and have not been cons- ered so far. In this book the most widely used mathematical models for the simulation of spray and mixture formation in 3D CFD calculations are described and discussed. In order to give the reader an introduction into the complex processes, the book starts with a description of the fundamental mechanisms and categories of fuel - jection, spray break-up, and mixture formation in internal combustion engines.
Author:
Publisher:
ISBN:
Category : Aeronautics
Languages : en
Pages : 702
Get Book Here
Book Description
Author: Lei Luo
Publisher: Frontiers Media SA
ISBN: 283251040X
Category : Technology & Engineering
Languages : en
Pages : 216
Get Book Here
Book Description
Author: Markus Raffel
Publisher: Springer Science & Business Media
ISBN: 3540723072
Category : Technology & Engineering
Languages : en
Pages : 460
Get Book Here
Book Description
This immensely practical guide to PIV provides a condensed, yet exhaustive guide to most of the information needed for experiments employing the technique. This second edition has updated chapters on the principles and extra information on microscopic, high-speed and three component measurements as well as a description of advanced evaluation techniques. What’s more, the huge increase in the range of possible applications has been taken into account as the chapter describing these applications of the PIV technique has been expanded.
Author: Sergei S. Sazhin
Publisher: Springer Nature
ISBN: 3030997464
Category : Technology & Engineering
Languages : en
Pages : 603
Get Book Here
Book Description
This book acts as a guide to simple models that describe some of the complex fluid dynamics, heat/mass transfer and combustion processes in droplets and sprays. Attention is focused mainly on the use of classical hydrodynamics, and a combination of kinetic and hydrodynamic models, to analyse the heating and evaporation of mono- and multi-component droplets. The models were developed for cases when small and large numbers of components are present in droplets. Some of these models are used for the prediction of time to puffing/micro-explosion of composite water/fuel droplets — processes that are widely used in combustion devices to stimulate disintegration of relatively large droplets into smaller ones. The predictions of numerical codes based on these models are validated against experimental results where possible. In most of the models, droplets are assumed to be spherical; some preliminary results of the generalisation of these models to the case of non-spherical droplets, approximating them as spheroids, are presented.
Author: Zhiyu Han
Publisher: SAE International
ISBN: 1468604015
Category : Technology & Engineering
Languages : en
Pages : 372
Get Book Here
Book Description
Simulation and Optimization of Internal Combustion Engines provides the fundamentals and up-to-date progress in multidimensional simulation and optimization of internal combustion engines. While it is impossible to include all the models in a single book, this book intends to introduce the pioneer and/or the often-used models and the physics behind them providing readers with ready-to-use knowledge. Key issues, useful modeling methodology and techniques, as well as instructive results, are discussed through examples. Readers will understand the fundamentals of these examples and be inspired to explore new ideas and means for better solutions in their studies and work. Topics include combustion basis of IC engines, mathematical descriptions of reactive flow with sprays, engine in-cylinder turbulence, fuel sprays, combustions and pollutant emissions, optimization of direct-injection gasoline engines, and optimization of diesel and alternative fuel engines.
Author: Guangyao Ouyang
Publisher: John Wiley & Sons
ISBN: 1119107237
Category : Technology & Engineering
Languages : en
Pages : 388
Get Book Here
Book Description
A wide-ranging and practical handbook that offers comprehensive treatment of high-pressure common rail technology for students and professionals In this volume, Dr. Ouyang and his colleagues answer the need for a comprehensive examination of high-pressure common rail systems for electronic fuel injection technology, a crucial element in the optimization of diesel engine efficiency and emissions. The text begins with an overview of common rail systems today, including a look back at their progress since the 1970s and an examination of recent advances in the field. It then provides a thorough grounding in the design and assembly of common rail systems with an emphasis on key aspects of their design and assembly as well as notable technological innovations. This includes discussion of advancements in dual pressure common rail systems and the increasingly influential role of Electronic Control Unit (ECU) technology in fuel injector systems. The authors conclude with a look towards the development of a new type of common rail system. Throughout the volume, concepts are illustrated using extensive research, experimental studies and simulations. Topics covered include: Comprehensive detailing of common rail system elements, elementary enough for newcomers and thorough enough to act as a useful reference for professionals Basic and simulation models of common rail systems, including extensive instruction on performing simulations and analyzing key performance parameters Examination of the design and testing of next-generation twin common rail systems, including applications for marine diesel engines Discussion of current trends in industry research as well as areas requiring further study Common Rail Fuel Injection Technology is the ideal handbook for students and professionals working in advanced automotive engineering, particularly researchers and engineers focused on the design of internal combustion engines and advanced fuel injection technology. Wide-ranging research and ample examples of practical applications will make this a valuable resource both in education and private industry.
Author: Yu Shi
Publisher: Springer Science & Business Media
ISBN: 0857296191
Category : Technology & Engineering
Languages : en
Pages : 323
Get Book Here
Book Description
Computational Optimization of Internal Combustion Engines presents the state of the art of computational models and optimization methods for internal combustion engine development using multi-dimensional computational fluid dynamics (CFD) tools and genetic algorithms. Strategies to reduce computational cost and mesh dependency are discussed, as well as regression analysis methods. Several case studies are presented in a section devoted to applications, including assessments of: spark-ignition engines, dual-fuel engines, heavy duty and light duty diesel engines. Through regression analysis, optimization results are used to explain complex interactions between engine design parameters, such as nozzle design, injection timing, swirl, exhaust gas recirculation, bore size, and piston bowl shape. Computational Optimization of Internal Combustion Engines demonstrates that the current multi-dimensional CFD tools are mature enough for practical development of internal combustion engines. It is written for researchers and designers in mechanical engineering and the automotive industry.
Author: Clayton T. Crowe
Publisher: CRC Press
ISBN: 1439840512
Category : Science
Languages : en
Pages : 509
Get Book Here
Book Description
Since the publication of the first edition of Multiphase Flow with Droplets and Particles, there have been significant advances in science and engineering applications of multiphase fluid flow. Maintaining the pedagogical approach that made the first edition so popular, this second edition provides a background in this important area of fluid mecha
