Author: Shigeru Hayashi
Publisher:
ISBN:
Category :
Languages : en
Pages : 0

Get Book Here

Book Description
Presented at the International Gas Turbine and Aeroengine Congress and Exposition, Houston, Texas - June 5-8, 1995.

Author: Rodrigo Villalva Gómez
Publisher:
ISBN:
Category :
Languages : en
Pages : 288

Get Book Here

Book Description
Experimental research on lean direct injection (LDI) combustors for gas turbine applications is presented. LDI combustion is an alternative to lean premixed combustion which has the potential of equivalent reduction of oxides of nitrogen (NOx) emissions and of peak combustor exit temperatures, but without some drawbacks of premixed combustors, such as flashback and autoignition. Simultaneous observations of the velocity field and reaction zone of an LDI swirl-stabilized combustor with a mixing tube at atmospheric conditions, with the goal of studying the flame stabilization mechanism, are shown. The flame was consistently anchored at the shear layer formed by the high-speed reactants exiting the mixing tube and the low speed recirculation region. Individual image analysis of the location of the tip of the recirculation zone and tip of the reaction region confirmed previously observed trends, but showed that calculation of the distance between these two points for corresponding image pairs yields results no different than when calculated from random image pairs. This most likely indicates a lag in the anchoring of the flame to changes in the recirculation zone, coupled with significant stochastic variation. An alternate LDI approach, multi-point LDI (MLDI), is also tested experimentally. A single large fuel nozzle is replaced by multiple small fuel nozzles to improve atomization and reduce the total volume of the high-temperature, low velocity recirculation zones, reducing NOx formation. The combustor researched employs a novel staged approach to allow good performance across a wide range of conditions by using a combination of nozzle types optimized to various power settings. The combustor has three independent fuel circuits referenced as pilot, intermediate, and outer. Emissions measurements, OH* chemiluminescence imaging, and thermoacoustic instability studies were run in a pressurized combustion facility at pressures from 2.0 to 5.3 bar.Combustor performance was analyzed for three fuel staging configurations, using local equivalence ratio of the individual circuits as a predictive parameter. Pilot-only mode enabled combustor operation at very low overall equivalence ratios while limiting NOx formation in idle power settings due to its configuration approximating a rich-quench-lean combustor. Pilot and intermediate staging tests demonstrated the range of equivalence ratios that are effective in reducing NOx formation while keeping other pollutants in check; very low equivalence ratio results in high unburned hydrocarbon and carbon monoxide, while very high equivalence ratios result in a detrimental effect as more fuel is routed through the intermediate fuel circuit. Using all three fuel circuits simultaneously in high power operation resulted in very low NOx levels (emissions index at or below 0.5 g/kg), particularly when fuel distribution was such that local equivalence ratio was equal among all circuits. The observed NOx levels compared favorably with other MLDI designs which do not have the operational flexibility of the combustor tested. Thermoacoustic instabilities occurred in the MLDI combustor for some test conditions. The local equivalence ratio of the intermediate fuel circuit was found to be one of the major predictor of the onset of instabilities. Detailed analysis of a two-circuit instability (pilot and intermediate) is presented.

Author:
Publisher:
ISBN:
Category : Mechanical engineering
Languages : en
Pages : 426

Get Book Here

Book Description

Author: H. S. Alkabie
Publisher:
ISBN:
Category :
Languages : en
Pages :

Get Book Here

Book Description

Author:
Publisher:
ISBN:
Category : Mechanical engineering
Languages : en
Pages : 754

Get Book Here

Book Description

Author: B. Ashok
Publisher: Elsevier
ISBN: 0128242280
Category : Technology & Engineering
Languages : en
Pages : 488

Get Book Here

Book Description
NOx Emission Control Technologies in Stationary and Automotive Internal Combustion Engines: Approaches Toward NOx Free Automobiles presents the fundamental theory of emission formation, particularly the oxides of nitrogen (NOx) and its chemical reactions and control techniques. The book provides a simplified framework for technical literature on NOx reduction strategies in IC engines, highlighting thermodynamics, combustion science, automotive emissions and environmental pollution control. Sections cover the toxicity and roots of emissions for both SI and CI engines and the formation of various emissions such as CO, SO2, HC, NOx, soot, and PM from internal combustion engines, along with various methods of NOx formation. Topics cover the combustion process, engine design parameters, and the application of exhaust gas recirculation for NOx reduction, making this book ideal for researchers and students in automotive, mechanical, mechatronics and chemical engineering students working in the field of emission control techniques. Covers advanced and recent technologies and emerging new trends in NOx reduction for emission control Highlights the effects of exhaust gas recirculation (EGR) on engine performance parameters Discusses emission norms such as EURO VI and Bharat stage VI in reducing global air pollution due to engine emissions

Author: H Zhao
Publisher: Elsevier
ISBN: 1845697456
Category : Technology & Engineering
Languages : en
Pages : 761

Get Book Here

Book Description
Volume 2 of the two-volume set Advanced direct injection combustion engine technologies and development investigates diesel DI combustion engines, which despite their commercial success are facing ever more stringent emission legislation worldwide. Direct injection diesel engines are generally more efficient and cleaner than indirect injection engines and as fuel prices continue to rise DI engines are expected to gain in popularity for automotive applications. Two exclusive sections examine light-duty and heavy-duty diesel engines. Fuel injection systems and after treatment systems for DI diesel engines are discussed. The final section addresses exhaust emission control strategies, including combustion diagnostics and modelling, drawing on reputable diesel combustion system research and development. Investigates how HSDI and DI engines can meet ever more stringent emission legislation Examines technologies for both light-duty and heavy-duty diesel engines Discusses exhaust emission control strategies, combustion diagnostics and modelling

Author: A. Tomita
Publisher: Elsevier
ISBN: 9780080440897
Category : Nature
Languages : en
Pages : 340

Get Book Here

Book Description
Over the past decade the topic of emissions reduction and control has remained an important area of research due to the enforcement of various Government policies in an attempt to minimize the impact on the environment. One area in which a great deal of research has been conducted to address this policy is NOx/SOx suppression. However, despite the progress that has been made over this time period, further research into the most effective method of reducing NOx/SOx emissions is still urgently required. In developed countries, a more stringent requirement in the level of emissions (such as is NOx/SOx component of less than 10ppm) will be enforced in the near future. Developing countries will also need a new technology that is effective and that is suited to each countries needs. Additional research and development efforts are thus necessary to meet such requirements. This compendium contains a collection of key papers themed around NOx/SOx emissions from combustion of hydrocarbon resources and the attempts to secure an efficient and effective method for reducing these emissions. These key papers are taken from the journals Fuel, Fuel Processing Technology and Progress in Energy and Combustion Science.

Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :

Get Book Here

Book Description
The combustion and emissions performance of fuel blends in modern combustion systems has been investigated with the intention of reducing emissions, improving efficiency and assessing the suitability of future automotive fuels. The combustion systems used in this study include Homogeneous Charge Compression Ignition (HCCI) and Direct Injection Spark Ignition (DISI). By adding a small quantity (10%) of diesel to gasoline, the HCCI combustion of this ̳Dieseline‘ mixture shows a 4% increase in the maximum and a 16% reduction in the minimum loads (IMEP) achievable. The NOX emissions are reduced, with greater than 30% savings seen for high engine loads. The addition of bio-fuels (ethanol and 2,5 di-methylfuran) to gasoline in HCCI combustion resulted in reduced ignitability giving rise to a 0.25 bar IMEP reduction of the maximum load. A 70% increase in NOX emissions is seen at an engine load of 3.5 bar IMEP. The addition of ethanol and to a lesser extent 2,5 di-methylfuran (DMF) to gasoline in DISI combustion shows increased combustion efficiency. The NOX emissions are reduced with ethanol, but are increased with the addition of DMF. At wide open throttle the bio-fuels show up to a 3 percentage point increase in efficiency through the use of more favourable spark timings brought about by the increased octane ratings and enthalpies of vaporisation. The PM emissions from DISI combustion can be reduced by up to 58% (mass) with the addition of ethanol. The soluble organic fraction forms a significant part of the total PM, particularly for the higher ethanol blends at wide open throttle. The addition of DMF however increases the total PM by up to 70% (mass) through the incomplete combustion of the ring structure.

Author: James S Harris
Publisher:
ISBN:
Category : Electronic dissertations
Languages : en
Pages : 0

Get Book Here

Book Description
Internal combustion engines are a key aspect of society, and their continued use poses challenges from an environmental standpoint since they emit pollutant and greenhouse gas emissions. This dissertation focuses on experimental analysis of dual-fuel low temperature combustion (LTC), which can be used as a strategy to reduce engine-out emissions and increase engine efficiencies. Dual fuel LTC uses two different fuels, a high reactivity fuel (HRF) and a low reactivity fuel (LRF). The HRF has a higher cetane number than the LRF, which allows for easier auto-ignition in compression ignition engines. Dual fuel engines also utilize high air to fuel ratios to achieve LTC. This, combined with early injection timings of the HRF, helps to reduce oxides of nitrogen (NOx) emissions. At low load conditions, this is a problem since higher cycle-to-cycle variations can increase pollutants such as unburned hydrocarbons (UHC) and carbon monoxide (CO). To combat this, a firm understanding of dual fuel LTC is required, as well as a strategy for reducing the cycle-to-cycle variations. The first part of this work further identifies a combustion heat release 'transformation region' across different HRF injection timings wherein in-cylinder conditions arise that are conducive for ultra-low NOx emissions. This phenomenon occurs for different IC engine platforms and different fueling combinations. An experimental analysis, 0D chemical kinetic analysis, and 3D computation fluid dynamic (CFD) analysis were combined to elucidate the underlying causes for this phenomenon. The local stratification level of the fuel/air mixture was identified as the likely cause of combustion heat release transformation with changing HRF injection timing. The second part of the present work builds upon the findings of the first part by utilizing local stratification to mitigate cycle-to-cycle variations that are present at low loads. A framework of experiments was formulated for both a low engine load of 5 bar gross indicated mean effective pressure (IMEPg) and a high load of 15 bar IMEPg, wherein an injection strategy concept termed Spray TArgeted Reactivity Stratification (STARS) was utilized using both diesel and Polyoxymethelene-dimethyl-ether (POMDME) as HRFs. A steep decrease in UHC and CO emissions (> 80% reductions) as well as improved engine operation stability were demonstrated using both HRFs with dual fuel LTC at 5 bar IMEPg. Further, potential for emissions mitigation and efficiency improvement are discussed, as well as differences in the experimental results shown between the differing HRFs.