An Experimental Study of Circular and Rectangular Thrust Augmenting Ejectors PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download An Experimental Study of Circular and Rectangular Thrust Augmenting Ejectors PDF full book. Access full book title An Experimental Study of Circular and Rectangular Thrust Augmenting Ejectors by Steven G. Reznick (CAPT, USAF.). Download full books in PDF and EPUB format.
Author: Steven G. Reznick (CAPT, USAF.)
Publisher:
ISBN:
Category : Ejector pumps
Languages : en
Pages : 116
Get Book Here
Book Description
Author: Steven G. Reznick (CAPT, USAF.)
Publisher:
ISBN:
Category : Ejector pumps
Languages : en
Pages : 116
Get Book Here
Book Description
Author: Gregory Unnever (CAPT, USAF.)
Publisher:
ISBN:
Category : Ejector pumps
Languages : en
Pages : 132
Get Book Here
Book Description
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 78
Get Book Here
Book Description
A short rectangular ejector and two circular ejectors were tested to determine the effects of primary nozzle configuration and geometry on thrust augmentation. The primary nozzle configurations consisted primarily of slot nozzles which injected fluid parallel to the diffuser walls and achieved Coanda type flow at the throat. Results of the rectangular ejector tests indicate that thin plates installed in the mixing chamber or the diffuser, increase mixing but decrease thrust augmentation. A continuous slot nozzle, modified to create four discrete jets at the inlet, improved mixing and thrust augmentation compared to the original design. Thrust augmentation ratio increased from 1.4 to 1.58. The circular ejector primary nozzles consisted of a continuous slot 'torus' nozzle and individual slot nozzles which could be symmetrically placed around the inlet periphery. A nozzle configuration using 16 slot nozzles on the periphery of the inlet face gave the best performance. A thrust augmentation ratio of 2.0 was achieved.
Author:
Publisher:
ISBN:
Category : Airplanes
Languages : en
Pages : 524
Get Book Here
Book Description
Author: Bruce Lowell Storms
Publisher:
ISBN:
Category : Ejector pumps
Languages : en
Pages : 140
Get Book Here
Book Description
Author: National Aeronautics and Space Adm Nasa
Publisher:
ISBN: 9781731249487
Category :
Languages : en
Pages : 132
Get Book Here
Book Description
Flow field measurements were obtained in a three-dimensional thrust augmenting ejector using laser Doppler velocimetry and hot wire anemometry. The primary nozzle, segmented into twelve slots of aspect ratio 3.0, was tested at a pressure ratio of 1.15. Results are presented on the mean velocity, turbulence intensity, and Reynolds stress progressions in the mixing chamber of the constant area ejector. The segmented nozzle was found to produce streamwise vortices that may increase the mixing efficiency of the ejector flow field. Compared to free jet results, the jet development is reduced by the presence of the ejector walls. The resulting thrust augmentation ratio of this ejector was also calculated to be 1.34. Storms, Bruce Lowell Unspecified Center EJECTORS; FLOW MEASUREMENT; LASER DOPPLER VELOCIMETERS; REYNOLDS STRESS; THREE DIMENSIONAL FLOW; THRUST AUGMENTATION; TURBULENCE EFFECTS; VORTICES; ASPECT RATIO; EXHAUST VELOCITY; HOT-WIRE ANEMOMETERS; NOZZLE DESIGN; PRESSURE RATIO; V/STOL AIRCRAFT...
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 61
Get Book Here
Book Description
An automated thrust augmentation data acquisition facility was designed and constructed. The facility provides the capability of measuring thrust augmentation ratio and mass flow augmentation ratio. A three dimensional graphics plot of exit flow is provided for flow analysis. Tests were conducted on a 4.4 in. diameter circular ejector, with eight primary nozzles mounted symmetrically along the perimeter of the inlet. A fixed ejector geometry was used. The ratio of mixing chamber area to diffuser exit area was 1.88. The fluid injection angle, measured from a line perpendicular to the ejector centerline, was varied and the thrust augmentation and mass flow augmentation ratios calculated. Both thrust augmentation and mass flow augmentation increased with fluid injection angle to the stall point where both decreased. Axial flow symmetry of primary air was found to affect stall along diffuser walls.
Author: S. G. Reznick
Publisher:
ISBN:
Category :
Languages : en
Pages : 12
Get Book Here
Book Description
Effects of primary jet inlet nozzle configuration and diffuser geometry on the thrust augmentation of circular and rectangular ejectors are investigated in an experimental study. The rectangular ejector inlet nozzle configurations consist of either one, two, or three slot nozzles. The circular ejector inlet nozzles consist of slot nozzles placed either across the inlet or around the inlet periphery. Diffuser geometry is varied primarily by changing the diffuser area ratio. Effect on thrust performance of the primary flow injection angle relative to the inlet walls is investigated. Effects of side-wall, end-wall, and diffuser blowing on thrust performance and diffuser stall also are considered.
Author: Generoso C. Uhuad (CAPT, USAF.)
Publisher:
ISBN:
Category : Ejector pumps
Languages : en
Pages : 178
Get Book Here
Book Description
Author: Generoso C. Uhuad
Publisher:
ISBN:
Category :
Languages : en
Pages : 115
Get Book Here
Book Description
A 4.4 in diameter circular ejector was tested to determine the effect on thrust augmentation ratio of the primary nozzle height and injection angle. Also tested were the effects of alternating primary nozzle injection angles, diffuser blowing and suction, inlet cross flow and low primary nozzle exit velocities on thrust augmentation. The results showed that both the primary nozzle injection angle and height affect the maximum thrust augmentation ratio attainable. A small amount of cross flow at the inlet increased the maximum thrust augmentation. The alternating primary nozzle injection angle arrangement did not increase the maximum thrust augmentation above that which was obtained using uniform primary nozzle injection angles. Diffuser blowing or suction did not provide an improvement in the maximum thrust augmentation above that which was obtained without diffuser boundary layer control. Finally, at low primary nozzle exit velocities, thrust augmentation increase as the nozzles were moved out along the inlet surface. The increase in thrust augmentation is attributed to the ability of the flow to remain attached to the inlet surface at low primary nozzle exit velocities thereby increasing the ejector effective mixing chamber length. (Author).
