The RF Power System for the SNS Linac PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download The RF Power System for the SNS Linac PDF full book. Access full book title The RF Power System for the SNS Linac by . Download full books in PDF and EPUB format.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 4
Get Book Here
Book Description
The initial goal of the SNS project is to produce a 1 MW average beam of protons with short pulse lengths onto a neutron-producing target. The objective of the SNS RF system is to generate 117 MW peak of pulsed 805 MHz microwave power with an accelerated beam pulse length of 1.04 ms at a 60 Hz repetition rate. The power system must be upgradeable in peak power to deliver 2 MW average power to the neutron target. The RF system also requires about 3 MW peak of RF power at 402.5 MHz, but that system is not discussed here. The design challenge is to produce an RF system at minimum cost, that is very reliable and economical to operate. The combination of long pulses and high repetition rates make conventional solutions, such as the pulse transformer and transmission line method, very expensive. The klystron, with a modulating anode, and 1.5 MW of peak output power is the baseline RF amplifier, an 56 are required in the baseline design. The authors discuss four power system configurations that are the candidates for the design. The baseline design is a floating-deck modulating anode system. A second power system being investigated is the fast-pulsed power supply, that can be turned on and off with a rise time of under 0.1 ms. This could eliminate the need for a modulator, and drastically reduce the energy storage requirements. A third idea is to use a pulse transformer with a series IGBT switch and a bouncer circuit on the primary side, as was done for the TESLA modulator. A fourth method is to use a series IGBT switch at high voltage, and not use a pulse transformer. The authors discuss the advantages and problems of these four types of power systems, but they emphasize the first two.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 4
Get Book Here
Book Description
The initial goal of the SNS project is to produce a 1 MW average beam of protons with short pulse lengths onto a neutron-producing target. The objective of the SNS RF system is to generate 117 MW peak of pulsed 805 MHz microwave power with an accelerated beam pulse length of 1.04 ms at a 60 Hz repetition rate. The power system must be upgradeable in peak power to deliver 2 MW average power to the neutron target. The RF system also requires about 3 MW peak of RF power at 402.5 MHz, but that system is not discussed here. The design challenge is to produce an RF system at minimum cost, that is very reliable and economical to operate. The combination of long pulses and high repetition rates make conventional solutions, such as the pulse transformer and transmission line method, very expensive. The klystron, with a modulating anode, and 1.5 MW of peak output power is the baseline RF amplifier, an 56 are required in the baseline design. The authors discuss four power system configurations that are the candidates for the design. The baseline design is a floating-deck modulating anode system. A second power system being investigated is the fast-pulsed power supply, that can be turned on and off with a rise time of under 0.1 ms. This could eliminate the need for a modulator, and drastically reduce the energy storage requirements. A third idea is to use a pulse transformer with a series IGBT switch and a bouncer circuit on the primary side, as was done for the TESLA modulator. A fourth method is to use a series IGBT switch at high voltage, and not use a pulse transformer. The authors discuss the advantages and problems of these four types of power systems, but they emphasize the first two.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
A high-intensity proton linac, such as that being planned for the SNS, requires accurate RF control of cavity fields for the entire pulse in order to avoid beam spill. The current design requirement for the SNS is RF field stability within "0.5% and "0.5{sup o} [1]. This RF control capability is achieved by the control electronics using the excess RF power to correct disturbances. To minimize the initial capital costs, the RF system is designed with 'just enough' RF power. All the usual disturbances exist, such as beam noise, klystron/HVPS noise, coupler imperfections, transport losses, turn-on and turn-off transients, etc. As a superconducting linac, there are added disturbances of large magnitude, including Lorentz detuning and microphonics. The effects of these disturbances and the power required to correct them are estimated, and the result shows that the highest power systems in the SNS have just enough margin, with little or no excess margin.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 4
Get Book Here
Book Description
A high-intensity proton linac, such as that being planned for the SNS, requires accurate RF control of cavity fields for the entire pulse in order to avoid beam spill. The current design requirement for the SNS is RF field stability within ±0.5% and ±0.5 . This RF control capability is achieved by the control electronics using the excess RF power to correct disturbances. To minimize the initial capital costs, the RF system is designed with 'just enough' RF power. All the usual disturbances exist, such as beam noise, klystron/HVPS noise, coupler imperfections, transport losses, turn-on and turn-off transients, etc. As a superconducting linac, there are added disturbances of large magnitude, including Lorentz detuning and microphonics. The effects of these disturbances and the power required to correct them are estimated, and the result shows that the highest power systems in the SNS have just enough margin, with little or no excess margin.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 3
Get Book Here
Book Description
The Spallation Neutron Source being built at the Oak Ridge National Lab in Tennessee requires a 1 GeV proton linac. Los Alamos has responsibility for the RF systems for the entire linac. The linac requires 3 distinct types of RF systems: 2.5-MW peak, 402.5 MHz, RF systems for the RFQ and DTL (7 systems total); 5-MW peak, 805 MHz systems for the CCL and the two energy corrector cavities (6 systems total); and 550-kW peak, 805 MHz systems for the superconducting sections (8 1 systems total). The design of the SNS Linac RF system was presented at the 2001 Particle Accelerator Conference in Chicago. Vendors have been selected for the klystrons (3 different vendors), circulators (I vendor), transmitter (1 vendor), and high power RF loads (3 different vendors). This paper presents the results and status of vendor procurements, test results of the major components of the Linac RF system and our installation progress.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
The Spallation Neutron Source (SNS) linac has a high gradient and 2 MW of beam power, and it therefore requires substantial RF power and cooling. There are 94 klystrons in its RF system, a large number for a proton linac. The optimization process and logic that lead to the klystron, transmitter, and power supply sizes is discussed. We also describe the requirements for building and tunnel area, electrical power, and water for this system. The trade-off decisions between low capital cost, low operating cost, and good maintainability are described.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 5
Get Book Here
Book Description
High Power Proton Linacs are under development or proposed for development at Los Alamos and elsewhere. By current standards these linacs all require very large amounts of RF power. The Accelerator for Production of Tritium (APT) is a CW accelerator with an output current and energy of 100 mA and 1,700 MeV, respectively. The Spallation Neutron Source (SNS), in its ultimate configuration, is a pulsed accelerator with an average output power of 4 MW of beam. Other accelerators such as those that address transmutation and upgrades to LANSCE have similar requirements. For these high average power applications, the RF systems represent approximately half of the total cost of the linac and are thus key elements in the design and configuration of the accelerator. Los Alamos is fortunate to be actively working on both APT and SNS. For these programs the author is pursuing a number of component developments which are aimed at one or more of the key issues for large RF systems: technical performance, capital cost, reliability, and operating efficiency. This paper briefly describes some of the linac applications and then provides updates on the key RF developments being pursued.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Spallation Neutron Source (SNS) accelerator includes a nominally 1000 MeV, 2 mA average current linac consisting of a radio frequency quadrapole (RFQ), drift tube linac (DTL), coupled cavity linac (CCL), a medium and high beta super conducting (SC) linac, and two buncher cavities for beam transport to the ring. Los Alamos is responsible for the RF systems for all sections of the linac. The SNS linac is a pulsed proton linac and the RF system must support a 1 msec beam pulse at up to a 60 Hz repetition rate. The RFQ and DTL utilize seven, 2.5 MW klystrons and operate at 402.5 MHz. The CCL, SC, and buncher cavities operate at 805 MHz. Six, 5 MW klystrons are utilized for the CCL and buncher cavities while eighty-one 550 kW klystrons are used for the SC cavities. All of the RF hardware for the SNS linac is currently in production. This paper will present details of the RF system-level design as well as specific details of the SNS RF equipment. The design parameters will be discussed. One of the design challenges has been achieving a reasonable cost with the very large number of high-power klystrons. The approaches we used to reduce cost and the resulting design compromises will be discussed.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
The Linac RF system is broken down into eight major components for this model. These components are: the klystrons, the waveguide, the water loads, the circulators, the converter/modulator, the transmitter, the window, and the low level RF (LLRF) controls. The mean time between failures (MTBF) for several of the components vary with voltage or klystron power level, and this variation is discussed below. In general, these MTBF's are design requirements supplied to the vendors of the subsystems, and verified at design reviews and by the experience at other accelerators. We assume that the scheduled operational time for the SNS is 6000 hours per year, and use this number to calculate the availability. We have to calculate the total down time during the 6000 hours of operation, and the availability is defined as one minus the unexpected down time for the year, divided by the number of operating hours in the year. Ideally, we would use distributions of MTBF's and MTTR's, since each failure will be different, but the equipment is not yet built, so the distributions are not available, and we make the assumption of constant MTBF and MTTR.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
This paper describes a procedure to set the phase and amplitude of the RF fields in the Spallation Neutron Source (SNS) linac's superconducting cavities. The linac uses superconducting cavities to accelerate the H− ion beam from the normal conducting linac at 185 MeV to a final energy of ≈1 GeV. There are two types of cavities in the linac, 33 cavities with a geometric beta of 0.61 and 48 cavities with a geometric beta of 0.81. The correct phase setting of any single superconducting cavity depends on the RF phase and amplitude of all the preceding superconducting cavities. For the beam to be properly accelerated it must arrive at each cavity with a relative phase ([phi]{sub s}), called the synchronous phase, of about -20 degrees. That is, it must arrive early with respect to the phase at which it would gain the maximum energy by 20 degrees. This timing provides the longitudinal focusing. Beam particles arriving slightly later gain more energy and move faster relative to the synchronous beam particle. The problem is to set the phase and amplitude of each cavity in the linac so that the synchronous particle arrives at each cavity with the correct phase. The amplitude of each superconducting cavity will be adjusted as high as possible constrained only by the available RF power and the breakdown field of the cavity.
Author: Ulf Kracht
Publisher:
ISBN:
Category :
Languages : en
Pages : 6
Get Book Here
Book Description
