Practical Directions for Marking and Adjusting the Corliss Valve Gear with One and Two Eccentrics PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Practical Directions for Marking and Adjusting the Corliss Valve Gear with One and Two Eccentrics PDF full book. Access full book title Practical Directions for Marking and Adjusting the Corliss Valve Gear with One and Two Eccentrics by Henry Harrison Kelley. Download full books in PDF and EPUB format.
Author: Henry Harrison Kelley
Publisher:
ISBN:
Category : Corliss valve gears
Languages : en
Pages : 36
Get Book Here
Book Description
Author: Henry Harrison Kelley
Publisher:
ISBN:
Category : Corliss valve gears
Languages : en
Pages : 36
Get Book Here
Book Description
Author: Henry Harrison Kelley
Publisher:
ISBN:
Category : Corliss valve gears
Languages : en
Pages : 31
Get Book Here
Book Description
Author: Henry Harrison Kelley
Publisher: Forgotten Books
ISBN: 9781330305218
Category : Technology & Engineering
Languages : en
Pages : 40
Get Book Here
Book Description
Excerpt from Practical Directions for Marking and Adjusting the Corliss Valve Gear: With One and Two Eccentrics In preparing the following instructions for setting and adjusting the standard type of Corliss valve gear, both single and double eccentric, it has been assumed that the reader is familiar with the construction of the standard form of Corliss gear, and with the operation of the gear when it is in proper working order. Having that much information to start with, the reader will find little difficulty in setting almost any make of Corliss engine valve gear, provided he will follow the instructions carefully and will carry-on the work, step by step, as directed. In the following instructions it is assumed that the eccentric is secured to the shaft by means of set screws, in which case the proper position of the eccentric must be determined. Thus the instructions will cover nearly all cases of failure of the gear and enable the engineer to substitute new parts and to set the entire gear correctly without the aid of marks usually put on the several parts by the builders. Lead and Tools. The amount of lead mentioned in this pamphlet is 1-32 of an inch, which is sufficient for all sizes of cylinders ordinarily met with in practice, excepting low pressure cylinders of compound engines, which usually require 1-16 of an inch lead. The tools required for marking and setting the gear are: Steel scriber, straight-edge, flexible scale 4 or 6 inches long, or a pair of dividers, 2-foot rule, sharp cold chisel and a hammer. Putting the Gear in Order. Before attempting to set the eccentric or to adjust the position of the wristplate and valves of the Corliss engine, the valve gear should be put into good working order. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Author: Henry Harrison Kelley
Publisher: Forgotten Books
ISBN: 9780331876093
Category : Technology & Engineering
Languages : en
Pages : 38
Get Book Here
Book Description
Excerpt from Practical Directions for Marking and Adjusting the Corliss Valve Gear: With One and Two Eccentrics If, upon removing the front bonnets from the valve chests, no marks are seen on the ends of the valves and on the valve seats, take the steam valves out, one at a time, and mark them, replacing one valve before removing another, so as not to get the valves into the wrong chests. Take a try-square and scriber, and, placing the blade parallel to the working edge of the valve, as shown in Fig. 2, draw a fine line to the end of the valve; then draw a radial line across the end of the valve to meet it, as shown in the same figure. After checking up to see that the lines are correctly located, take -a sharp chisel and make the radial line deeper near the edge of the valve. About the Publisher Forgotten Books publishes hundreds of thousands of rare and classic books. Find more at www.forgottenbooks.com This book is a reproduction of an important historical work. Forgotten Books uses state-of-the-art technology to digitally reconstruct the work, preserving the original format whilst repairing imperfections present in the aged copy. In rare cases, an imperfection in the original, such as a blemish or missing page, may be replicated in our edition. We do, however, repair the vast majority of imperfections successfully; any imperfections that remain are intentionally left to preserve the state of such historical works.
Author: Henry Harrison Kelley
Publisher: Wentworth Press
ISBN: 9781363577514
Category : History
Languages : en
Pages : 38
Get Book Here
Book Description
This work has been selected by scholars as being culturally important, and is part of the knowledge base of civilization as we know it. This work was reproduced from the original artifact, and remains as true to the original work as possible. Therefore, you will see the original copyright references, library stamps (as most of these works have been housed in our most important libraries around the world), and other notations in the work. This work is in the public domain in the United States of America, and possibly other nations. Within the United States, you may freely copy and distribute this work, as no entity (individual or corporate) has a copyright on the body of the work. As a reproduction of a historical artifact, this work may contain missing or blurred pages, poor pictures, errant marks, etc. Scholars believe, and we concur, that this work is important enough to be preserved, reproduced, and made generally available to the public. We appreciate your support of the preservation process, and thank you for being an important part of keeping this knowledge alive and relevant.
Author: Henry Harrison Kelley
Publisher:
ISBN:
Category : Corliss valve gears
Languages : en
Pages : 63
Get Book Here
Book Description
Author: Robert Alexander Peddie
Publisher:
ISBN:
Category : Engineering
Languages : en
Pages : 268
Get Book Here
Book Description
Author: Sanford Alexander Moss
Publisher:
ISBN:
Category : Machine design
Languages : en
Pages : 178
Get Book Here
Book Description
Author: Terrell Croft
Publisher:
ISBN:
Category : Steam-engines
Languages : en
Pages : 536
Get Book Here
Book Description
Author:
Publisher:
ISBN:
Category : Electric engineering
Languages : en
Pages : 200
Get Book Here
Book Description
