Numerical Study of Film Cooling Influence on Performance of Transonic Vane Cascade PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Numerical Study of Film Cooling Influence on Performance of Transonic Vane Cascade PDF full book. Access full book title Numerical Study of Film Cooling Influence on Performance of Transonic Vane Cascade by Ahmad Mahmoud Alameldin. Download full books in PDF and EPUB format.
Author: Ahmad Mahmoud Alameldin
Publisher:
ISBN:
Category : Aircraft gas-turbines
Languages : en
Pages : 144
Get Book Here
Book Description
Abstract: Gas turbines are a major contributor to world power generation with applications ranging from electricity production to aircrafts propulsion. Their efficiency is subject to continuous research. A gas turbine's overall efficiency is directly proportional to flow inlet temperature. Various methods are implemented to protect hot gas path components from mainstream flow well above their melting temperature, namely, heat resistant coatings, internal cooling and film cooling. The latter is the subject of this work. A 3-D Computational Fluid Dynamics (CFD) model is solved using ANSYS CFX software and compared to experimental measurements of film cooled transonic vane cascade operating at a Mach number of 0.89; the experimental data used for validation is provided by Heat and Power Technology Department of the Royal Institute of Technology (Kungliga Tekniska Hogskolan, KTH) of Stockholm, Sweden. A new approach was used to model the film cooling holes, omitting the need to model both the coolant plenum and cooling tubes, resulting in 180% reduction in grid size and attributed computational cost interpreted in 300% saving in computation time. The new approach was validated on a basic flow problem (flat plate film cooling) and was found to give good agreement with experimental measurements of velocity and temperature at a blowing ratio (BR) of 1 and 2; the experimental data for the flat plate was provided by NASA's Glenn Research Center. The numerical simulation of the cooled vane cascade was compared to experimental measurements for different cooling configurations and different BRs. a) One row on pressure side at BR = 0.8, 0.96 and 2.5. b) Two rows on suction side (location 1) at BR = 0.8, 1.4 and 2.5. c) Two rows on suction side (location 2) at BR = 0.8. And d) Showerhead cooled vane at BR ranges between 1.98 and 5.84. The coolant was applied at the same temperature as the mainstream, to match experimental conditions. A good agreement with the experimental measurements was obtained for exit flow angle, vorticity downstream of the vane, pressure coefficients and aerodynamic loss. The proposed approach of coolant injection modeling is shown to yield reliable results, within the uncertainty of the measurements in most cases. Along with lower computational cost compared to conventional film cooling modeling approach, the new approach is recommended for further analysis for aero and thermal vane cascade flows.
Author: Ahmad Mahmoud Alameldin
Publisher:
ISBN:
Category : Aircraft gas-turbines
Languages : en
Pages : 144
Get Book Here
Book Description
Abstract: Gas turbines are a major contributor to world power generation with applications ranging from electricity production to aircrafts propulsion. Their efficiency is subject to continuous research. A gas turbine's overall efficiency is directly proportional to flow inlet temperature. Various methods are implemented to protect hot gas path components from mainstream flow well above their melting temperature, namely, heat resistant coatings, internal cooling and film cooling. The latter is the subject of this work. A 3-D Computational Fluid Dynamics (CFD) model is solved using ANSYS CFX software and compared to experimental measurements of film cooled transonic vane cascade operating at a Mach number of 0.89; the experimental data used for validation is provided by Heat and Power Technology Department of the Royal Institute of Technology (Kungliga Tekniska Hogskolan, KTH) of Stockholm, Sweden. A new approach was used to model the film cooling holes, omitting the need to model both the coolant plenum and cooling tubes, resulting in 180% reduction in grid size and attributed computational cost interpreted in 300% saving in computation time. The new approach was validated on a basic flow problem (flat plate film cooling) and was found to give good agreement with experimental measurements of velocity and temperature at a blowing ratio (BR) of 1 and 2; the experimental data for the flat plate was provided by NASA's Glenn Research Center. The numerical simulation of the cooled vane cascade was compared to experimental measurements for different cooling configurations and different BRs. a) One row on pressure side at BR = 0.8, 0.96 and 2.5. b) Two rows on suction side (location 1) at BR = 0.8, 1.4 and 2.5. c) Two rows on suction side (location 2) at BR = 0.8. And d) Showerhead cooled vane at BR ranges between 1.98 and 5.84. The coolant was applied at the same temperature as the mainstream, to match experimental conditions. A good agreement with the experimental measurements was obtained for exit flow angle, vorticity downstream of the vane, pressure coefficients and aerodynamic loss. The proposed approach of coolant injection modeling is shown to yield reliable results, within the uncertainty of the measurements in most cases. Along with lower computational cost compared to conventional film cooling modeling approach, the new approach is recommended for further analysis for aero and thermal vane cascade flows.
Author: James C. Kullberg
Publisher:
ISBN:
Category :
Languages : en
Pages : 105
Get Book Here
Book Description
Many studies have been published on the subject of film cooling, but because of the difficulty and expense of simulating turbine realistic conditions, many authors introduce vast simplifications such as low speed conditions or linear cascades. These simplifications do not adequately represent the behavior of a turbine and therefore their results are of limited use. This study attempts to eliminate many of those simplifications.
Author: Isabella Gayoso
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Get Book Here
Book Description
In this experiment, measurements of the overall cooling effectiveness for a film cooled turbine vane airfoil in a high-speed cascade were obtained using infrared thermography. The vane used was the NASA C3X with impingement holes (showerhead cooling) and convective cooling holes on both the suction and pressure side. This work was done in the Mechanical Engineering Department's Experimental and Computational Convection Lab and used the high-speed cascade capability of the lab. The rationale for conducting this work was to obtain experimental data on film cooling effectiveness in a turbine vane in engine-like conditions at transonic speeds. Previous work has been done at subsonic speeds, but few pieces of literature examine this parameter at transonic speeds. The data can then be used to validate or compare to CFD models and to better understand what happens to the vane temperature distribution during engine operation. This understanding could inform the design of film cooling holes to reduce thermal strain "hot spots" which lead to failure of the vane. The results showed that trends for values of overall film effectiveness were as expected in this experiment, such as increases in blowing ratio correlating to increases in overall film effectiveness. However, the blowing ratios used in this study were not as high as values studied previously, indicating a need for more data on overall film effectiveness at transonic speeds.
Author: Mulugeta K. Berhe
Publisher:
ISBN:
Category :
Languages : en
Pages : 314
Get Book Here
Book Description
Author: Lei Luo
Publisher: Frontiers Media SA
ISBN: 283251040X
Category : Technology & Engineering
Languages : en
Pages : 216
Get Book Here
Book Description
Author: Xuezhi Zhang
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Get Book Here
Book Description
This work presents the performance of a louver film-cooling scheme under different operating conditions. The louver cooling scheme consists of a bend by which the coolant going through the flow passage is redirected from vertical to horizontal direction before being injected into the mainstream through an expanded exit. Not only is the momentum of the coolant converted to the mainstream direction, but it is also reduced by the expanded exit before injection. The impingement of the coolant on the blade surface inside the bend also enables further cooling on the targeted surface. The louver cooling scheme was tested under a variety of conditions, from a flat plate to airfoils, from low speed incompressible flows to transonic flows, from a stationary airfoil to a rotating airfoil, and from the leading edge to the middle of an airfoil. Unsteady analysis using a DES (Detached Eddy Simulation) model was also carried out to evaluate its ability to accurately simulate film cooling by comparing with steady state analysis. In general, the louver cooling scheme has been proved to provide enhanced cooling protection to the targeted surface in comparison with other cooling schemes in all conditions tested. At low speed incompressible flow conditions, a higher blowing ratio led to a higher cooling effectiveness. At transonic flow conditions, a moderately higher blowing ratio also proved helpful with a higher cooling effectiveness. Very high blowing ratios, however, proved to be detrimental to the cooling performance since strong detached shock wave structures due to high blowing ratios caused boundary layer separation, rendering the coolant virtually ineffective. The rotation of blade was found to have a significant impact on the level of cooling effectiveness at the leading edge of an airfoil. With regard to the cooling performance, blowing ratio was the dominant factor at low rotational speeds and the rotational speed was the dominant factor at high blowing ratios for circular holes. For the louver scheme as jet liftoff was avoided, effectiveness increased with rotating speed. Results also showed that, unsteady analysis was not significantly more accurate than steady analysis. The unsteady analysis did capture the coolant lateral spreading better, with a high cost of computing, however. Results in this work show that shock waves encountered on transonic airfoils had a significant impact on film cooling effectiveness on any shaped holes. Therefore, experimental data obtained under low speed test should be used with great caution in real design of turbine blade cooling. There are fundamental differences in film cooling between at the leading edge and elsewhere on an airfoil in that a slight incidence shifting due to turbine rotating speed may cause a sudden decrease in cooling effectiveness level at high blowing ratios for circular hole. This could lead to a catastrophic failure if the blade is already in a weak and stressed state. Using of shaped holes with expanded exits may prevent this from happening.
Author: Hugh W. Coleman
Publisher: John Wiley & Sons
ISBN: 1119417708
Category : Technology & Engineering
Languages : en
Pages : 404
Get Book Here
Book Description
Helps engineers and scientists assess and manage uncertainty at all stages of experimentation and validation of simulations Fully updated from its previous edition, Experimentation, Validation, and Uncertainty Analysis for Engineers, Fourth Edition includes expanded coverage and new examples of applying the Monte Carlo Method (MCM) in performing uncertainty analyses. Presenting the current, internationally accepted methodology from ISO, ANSI, and ASME standards for propagating uncertainties using both the MCM and the Taylor Series Method (TSM), it provides a logical approach to experimentation and validation through the application of uncertainty analysis in the planning, design, construction, debugging, execution, data analysis, and reporting phases of experimental and validation programs. It also illustrates how to use a spreadsheet approach to apply the MCM and the TSM, based on the authors’ experience in applying uncertainty analysis in complex, large-scale testing of real engineering systems. Experimentation, Validation, and Uncertainty Analysis for Engineers, Fourth Edition includes examples throughout, contains end of chapter problems, and is accompanied by the authors’ website www.uncertainty-analysis.com. Guides readers through all aspects of experimentation, validation, and uncertainty analysis Emphasizes the use of the Monte Carlo Method in performing uncertainty analysis Includes complete new examples throughout Features workable problems at the end of chapters Experimentation, Validation, and Uncertainty Analysis for Engineers, Fourth Edition is an ideal text and guide for researchers, engineers, and graduate and senior undergraduate students in engineering and science disciplines. Knowledge of the material in this Fourth Edition is a must for those involved in executing or managing experimental programs or validating models and simulations.
Author: National Aeronautics and Space Administration (NASA)
Publisher: Createspace Independent Publishing Platform
ISBN: 9781723439759
Category :
Languages : en
Pages : 178
Get Book Here
Book Description
The progress under contract NAS3-24619 toward the goal of establishing a relevant data base for use in improving the predictive design capabilities for external heat transfer to turbine vanes, including the effect of downstream film cooling with and without leading edge showerhead film cooling. Experimental measurements were made in a two-dimensional cascade previously used to obtain vane surface heat transfer distributions on nonfilm cooled airfoils under contract NAS3-22761 and leading edge showerhead film cooled airfoils under contract NAS3-23695. The principal independent parameters (Mach number, Reynolds number, turbulence, wall-to-gas temperature ratio, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio) were maintained over ranges consistent with actual engine conditions and the test matrix was structured to provide an assessment of the independent influence of parameters of interest, namely, exit Mach number, exit Reynolds number, coolant-to-gas temperature ratio, and coolant-to-gas pressure ratio. Data provide a data base for downstream film cooled turbine vanes and extends the data bases generated in the two previous studies. The vane external heat transfer obtained indicate that considerable cooling benefits can be achieved by utilizing downstream film cooling. The data obtained and presented illustrate the interaction of the variables and should provide the airfoil designer and computational analyst the information required to improve heat transfer design capabilities for film cooled turbine airfoils. Hylton, L. D. and Nirmalan, V. and Sultanian, B. K. and Kaufman, R. M. Unspecified Center EQUIPMENT SPECIFICATIONS; FILM COOLING; HEAT TRANSFER; LEADING EDGES; STRUCTURAL DESIGN; VANES; AIRCRAFT ENGINES; CASCADE FLOW; DATA PROCESSING; GAS TURBINES; HIGH TEMPERATURE; PARAMETERIZATION; TWO DIMENSIONAL FLOW...
Author: Je-Chin Han
Publisher: CRC Press
ISBN: 1439855684
Category : Science
Languages : en
Pages : 892
Get Book Here
Book Description
A comprehensive reference for engineers and researchers, Gas Turbine Heat Transfer and Cooling Technology, Second Edition has been completely revised and updated to reflect advances in the field made during the past ten years. The second edition retains the format that made the first edition so popular and adds new information mainly based on selected published papers in the open literature. See What’s New in the Second Edition: State-of-the-art cooling technologies such as advanced turbine blade film cooling and internal cooling Modern experimental methods for gas turbine heat transfer and cooling research Advanced computational models for gas turbine heat transfer and cooling performance predictions Suggestions for future research in this critical technology The book discusses the need for turbine cooling, gas turbine heat-transfer problems, and cooling methodology and covers turbine rotor and stator heat-transfer issues, including endwall and blade tip regions under engine conditions, as well as under simulated engine conditions. It then examines turbine rotor and stator blade film cooling and discusses the unsteady high free-stream turbulence effect on simulated cascade airfoils. From here, the book explores impingement cooling, rib-turbulent cooling, pin-fin cooling, and compound and new cooling techniques. It also highlights the effect of rotation on rotor coolant passage heat transfer. Coverage of experimental methods includes heat-transfer and mass-transfer techniques, liquid crystal thermography, optical techniques, as well as flow and thermal measurement techniques. The book concludes with discussions of governing equations and turbulence models and their applications for predicting turbine blade heat transfer and film cooling, and turbine blade internal cooling.
Author: C. R. B. Day
Publisher:
ISBN:
Category :
Languages : en
Pages : 0
Get Book Here
Book Description
Presented at the International Gas Turbine & Aeroegine Congress & Exhibition, Orlando, FL, Jun 2-Jun 5, 1997.
