Modeling of Contact Between Liner Finish and Piston Ring in Internal Combustion Engines Based on 3D Measured Surface PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Modeling of Contact Between Liner Finish and Piston Ring in Internal Combustion Engines Based on 3D Measured Surface PDF full book. Access full book title Modeling of Contact Between Liner Finish and Piston Ring in Internal Combustion Engines Based on 3D Measured Surface by Qing Zhao (S.M.). Download full books in PDF and EPUB format.
Author: Qing Zhao (S.M.)
Publisher:
ISBN:
Category :
Languages : en
Pages : 88
Get Book Here
Book Description
When decreasing of fossil fuel supplies and air pollution are two major society problems in the 21st century, rapid growth of internal combustion (IC) engines serves as a main producer of these two problems. In order to increase fuel efficiency, mechanical loss should be controlled in internal combustion engines. Interaction between piston ring pack and cylinder liner finish accounts for nearly 20 percent of the mechanical losses within an internal combustion engine, and is an important factor that affects the lubricant oil consumption. Among the total friction between piston ring pack and cylinder liner, boundary friction occurs when piston is at low speed and there is direct contact between rings and liners. This work focuses on prediction of contact between piston ring and liner finish based on 3D measured surface and different methods are compared. In previous twin-land oil control ring (TLOCR) deterministic model, Greenwood-Tripp correlation function was used to determine contact. The practical challenge for this single equation is that real plateau roughness makes it unreliable. As a result, micro geometry of liner surface needs to be obtained through white light interferometry device or confocal equipment to conduct contact model. Based on real geometry of liner finish and the assumption that ring surface is ideally smooth, contact can be predicted by three different models which were developed by using statistical Greenwood-Williamson model, Hertzian contact and revised deterministic dry contact model by Professor A.A. Lubrecht. The predicted contact between liner finish and piston ring is then combined with hydrodynamic pressure caused by lubricant which was examined using TLOCR deterministic model by Chen. et al to get total friction resulted on the surface of liner finish. Finally, contact model is used to examine friction of different liners in an actual engine running cycle.
Author: Qing Zhao (S.M.)
Publisher:
ISBN:
Category :
Languages : en
Pages : 88
Get Book Here
Book Description
When decreasing of fossil fuel supplies and air pollution are two major society problems in the 21st century, rapid growth of internal combustion (IC) engines serves as a main producer of these two problems. In order to increase fuel efficiency, mechanical loss should be controlled in internal combustion engines. Interaction between piston ring pack and cylinder liner finish accounts for nearly 20 percent of the mechanical losses within an internal combustion engine, and is an important factor that affects the lubricant oil consumption. Among the total friction between piston ring pack and cylinder liner, boundary friction occurs when piston is at low speed and there is direct contact between rings and liners. This work focuses on prediction of contact between piston ring and liner finish based on 3D measured surface and different methods are compared. In previous twin-land oil control ring (TLOCR) deterministic model, Greenwood-Tripp correlation function was used to determine contact. The practical challenge for this single equation is that real plateau roughness makes it unreliable. As a result, micro geometry of liner surface needs to be obtained through white light interferometry device or confocal equipment to conduct contact model. Based on real geometry of liner finish and the assumption that ring surface is ideally smooth, contact can be predicted by three different models which were developed by using statistical Greenwood-Williamson model, Hertzian contact and revised deterministic dry contact model by Professor A.A. Lubrecht. The predicted contact between liner finish and piston ring is then combined with hydrodynamic pressure caused by lubricant which was examined using TLOCR deterministic model by Chen. et al to get total friction resulted on the surface of liner finish. Finally, contact model is used to examine friction of different liners in an actual engine running cycle.
Author: Haijie Chen
Publisher:
ISBN:
Category :
Languages : en
Pages : 133
Get Book Here
Book Description
Piston ring packs are used in internal combustion engines to seal both the high pressure gas in the combustion chamber and the lubricant oil in the crank case. The interaction between the piston ring pack and the cylinder bore contributes substantially to the total friction power loss for IC engines. The aim of this thesis work is to advance the understanding of the ring liner lubrication through numerical modeling. A twin-land oil control ring lubrication model and a top two-ring lubrication model are developed based on a deterministic approach. The models take into consideration the effect of both the liner finish micro geometry and the ring face macro profile. The liner finish effect is evaluated on a 3D deterministically measured liner finish patch, with fully-flooded oil supply condition to the oil control rings and starved oil supply condition to the top two rings. Correlations based on deterministic calculations and proper scaling are developed to connect the average hydrodynamic pressure and friction to the critical geometrical parameters and operating parameters so that cycle evaluation of the ring lubrication can be performed in an efficient manner. The models can be used for ring pack friction prediction, and ring pack/liner design optimization based on the trade-off of friction power loss and oil consumption. To provide further insights to the effect of liner finish, a wear model is then developed to simulate the liner surface geometry evolution during the break-in/wear process. The model is based on the idea of simulated repetitive grinding on the plateau part of the liner finish using a random grinder. The model successfully captures the statistic topological features of the worn liner roughness. Combining the piston ring pack model and the liner finish wear model, one can potentially predict the long term ring pack friction loss. Finally the thesis covers the experimental validation of the twin-land oil control ring model using floating liner engine friction measurements. The modeled ring friction is compared with the experimental measurement under different ring designs and liner finishes. The result shows that the model in general successfully predicts the friction force of the twin-land oil control ring/liner pair.
Author: Haijie Chen
Publisher:
ISBN:
Category :
Languages : en
Pages : 119
Get Book Here
Book Description
(cont.) These key parameters include the surface wavelength of the plateau part, the frequency of deep valleys and the honing cross-hatch angle. This thesis work has opened a window on the deterministic study of the functionality of cylinder liner surface texture.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages : 77
Get Book Here
Book Description
Internal combustion (IC) engines are broadly utilized today. The friction caused by piston rings in IC engines contributes around 20% of the mechanical friction losses. The liner finish is the most critical parameter to define the tension and other design parameters of the piston rings for proper sealing. This work is focused on developing numerical approaches to generating liner finishes based on certain values of topology parameters. The generated surface is able to simulate the lubrication and dry contact behaviors of the original surface, so that the method is used to study the effects of various topology parameters on friction losses. First, methods to analyze, generate, test, and compare honed liner surfaces have been developed. The algorithm to analyze the topology parameters of honed surfaces is described. The honed surfaces are numerically generated and compared with the experimental data. Moreover, the topological variables are changed and the corresponding friction behaviors are studied. The relations between topology variables and friction losses are illustrated. We also developed a quantitative relation between two ISO standards describing the honed liner finish, so that the manufacturing industry can use the surface generation method in convenience. Second, attempts were made to simulate the break-in processes for honed liner finish. Measured and numerically generated surfaces are simulated and compared. The friction and pressure behaviors for lightly and heavily worn surfaces are compared with experimental data. Moreover, by tuning the worn parameters, the friction effective mean pressure (FMEP) curve can match the experimental data. Finally, the algorithm to numerically generate thermally sprayed liner finish is described. The hydrodynamic and dry contact friction behaviors for generated surfaces are compared with experimental data. Critical topology parameters are tuned and their effects on friction losses are studied. Moreover, the effects of the pores created by the plasma spraying processes on the lubrication behaviors are simulated.
Author: Chongjie Gu
Publisher:
ISBN:
Category :
Languages : en
Pages : 108
Get Book Here
Book Description
Internal combustion engines are widely utilized in modem automobiles. Around 10% of the total fuel energy is dissipated to heat due to mechanical friction, among which 20% is caused by the contact between the cylinder liner and the piston rings. The wear of cylinder liner not only leads to surface damage, but also results in the change of liner lubrication conditions. Therefore, a large number of tests are performed by researchers to investigate the liner wear process and its impact on engine lubrication. This work is the first step toward developing a wear model to predict the evolution of liner roughness and ring pack lubrication during break-in period. A physics-based liner wear model is built in this work, with focus on two mechanisms: surface plastic flattening and fatigue wear. Both mechanisms are simulated through a set of governing equations and are coupled together to complete the algorithm of the liner wear model. Simulations of break-in wear are performed to different liner surfaces finishes, with different external normal pressures. Simulation results indicate that the liner wear rate depends on the size and shape of liner surface asperities, which may provide guidance for surface manufacturing. The results also show consistence with the Archard's wear law, describing the proportional correlation between normal pressure and steady state wear rate. This wear model is then used to study the influence of liner wear on engine lubrication. Through the friction for entire engine cycles, simulated results are compared with experimental friction measurements. The comparison shows that the calculated friction evolution during break-in has the same trend and comparable magnitude as the measurements, indicating the efficiency of the wear model. Some initial work of modeling of third-body abrasive wear is also discussed in this thesis.
Author: Yang Liu (S.M.)
Publisher:
ISBN:
Category :
Languages : en
Pages : 109
Get Book Here
Book Description
Nowadays, a rapid growth of internal combustion (IC) engines is considered to be a major contributor to energy crisis. About 20% of the mechanical loss in internal combustion engines directly goes to the friction loss between piston ring pack and liner finish. A twin-land oil control ring (TLOCR) deterministic model was developed by Chen et al. and it helps the automotive companies investigate the effects of liner finish, rings, and lubricants on friction and oil control of the TLOCR [2]. This work focuses on application of the TLOCR model and extension of the deterministic model to the top two rings. First, there are some practical challenges in the application of Chen's TLOCR deterministic model. Due to different wear condition on the same liner, surface roughness varies from spot to spot. A small patch of measurement cannot provide enough information and the change of plateau roughness makes the contact model unreliable. As a result, a multi-point correlation method was proposed to combine the information of different spots from the same liner and this method was shown to give better match to the experimental results. A top-two-ring lubrication cycle model was developed based on the multiphase deterministic model by Li. et al [30] and previous top-two-ring lubrication model by Chen. Et al [2][31]. The model is composed with two parts. First, the deterministic model is used to generate a correlation between the hydrodynamic pressure/friction and the minimum clearance with prescribed oil supply from the deterministic oil control ring model. It was found that within reasonable accuracy, the gas pressure effect on the hydrodynamic lubrication of the top two rings can be decoupled from the hydrodynamic lubrication. Thus, only single-phase deterministic model was needed to generate the correlation. This decoupling significantly reduces the computation time. Then, a cycle model was developed utilizing the correlation of hydrodynamic pressure/friction and the minimum clearance. The cycle model considers the effect of gas pressure variations in different ring pack regions as well as the dynamic twist of the top two rings. Finally, the models were used to examine the friction and lubrication of three different liner finishes in an actual engine running cycle.
Author: Dian Xu
Publisher:
ISBN:
Category :
Languages : en
Pages : 72
Get Book Here
Book Description
In the process of designing internal combustion engine, piston ring plays an important role in fulfilling the requirements of camber gas sealing, friction reduction and lubrication oil consumption. The goal of this thesis is to have a better understanding of the ring behaviors under different working conditions in a structural level. This thesis is an extension of existing ring design tool. A model is built up to simulate the processes of changing ring states from one to another such as free or fit the ring. It revealed the sensitive characters of the piston ring tip; it expanded the field of application of the existing piston ring design tool; it also investigated the ring bore interaction in more conditions. This work removed the symmetric assumption in the existing tool. A new method that calculates ring free shape and ring bore contact force from ring ovality data is introduced for the first time. The analysis of ring bore interaction is widened. The model was applied to an industry ring design case. In this case it shows the free and fit procedure in this model is physically and mathematically reversible. It shows these procedures are direction independent. The contact force distribution changes when the ring is moving within the distorted bore. It also changes when the wetting or roughness situation is different. This model can calculate the ring free shape from asymmetric measured ovality data. It can also retrieve the desired contact force from it. The piston ring design tool is updated and implemented with these highly appreciable new features. This complete package has high efficiency and a wider practical field.
Author:
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
By Tian Tian.
Author: Kevin C. Radil
Publisher:
ISBN:
Category : Ceramic coating
Languages : en
Pages : 14
Get Book Here
Book Description
Reciprocating wear tests were performed to investigate the effects of honing on the wear of ceramic coated piston rings and cylinder liners. The baseline or control cases consisted of testing ceramic coated rings against ceramic coated liner specimens whose surfaces were ground and lapped smooth. A second series of tests were performed with liner specimens with base and plateau honed surfaces. Test conditions were chosen to simulate the temperatures, pressures, and boundary lubricated conditions present at top ring reversal in a conventional diesel engine. Wear factor comparisons between the baseline cases and the tests with the honed liner specimens indicate that honing alone is not sufficient to ensure an improvement in ring and liner wear.
Author: Tian Tian
Publisher:
ISBN:
Category :
Languages : en
Pages : 388
Get Book Here
Book Description
