Evaluation of Film Cooling Superposition Method on the Suction Side of a Blade Model PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Evaluation of Film Cooling Superposition Method on the Suction Side of a Blade Model PDF full book. Access full book title Evaluation of Film Cooling Superposition Method on the Suction Side of a Blade Model by Christopher Yoon. Download full books in PDF and EPUB format.
Author: Christopher Yoon
Publisher:
ISBN:
Category :
Languages : en
Pages : 126
Get Book Here
Book Description
Film cooling is often used for turbine airfoil cooling, and there are numerous studies of the performance of a single row of holes. Typically, blades and vanes in gas turbine engines have multiple rows of holes that interact. Consequently, there is a need to develop techniques to predict film cooling performance with multiple rows of holes. One of the method is to superposition single row cooling effectiveness to predict combined effectiveness. Although there have been many studies of superposition techniques with multiple rows of cylindrical holes, there have been very few in which shaped holes were used with a typical turbine airfoil model. In this study, film effectiveness was measured on the suction side of a turbine blade model using two rows of 7-7-7 shaped holes, with pitch to diameter ratio of 6, and the two rows were more than 40 diameters apart. Measurements were made with each row operating independently, which provided the experimental data for superposition predictions. These predictions were evaluated with effectiveness measurements with both rows operational. For these combined row tests, two different upstream blowing ratios and a wide range of downstream blowing ratios were selected. The superposition predictions were reasonably accurate when the upstream blowing ratio was high with a corresponding smaller film effectiveness downstream (due to jet separation). However, when the upstream coolant holes were operated at optimum blowing ratio with maximum film effectiveness downstream, the superposition analysis predicted film effectiveness levels slightly lower than actual levels. These results indicate that there was an interaction between jets that resulted in higher film effectiveness than what the superposition method had predicted
Author: Christopher Yoon
Publisher:
ISBN:
Category :
Languages : en
Pages : 126
Get Book Here
Book Description
Film cooling is often used for turbine airfoil cooling, and there are numerous studies of the performance of a single row of holes. Typically, blades and vanes in gas turbine engines have multiple rows of holes that interact. Consequently, there is a need to develop techniques to predict film cooling performance with multiple rows of holes. One of the method is to superposition single row cooling effectiveness to predict combined effectiveness. Although there have been many studies of superposition techniques with multiple rows of cylindrical holes, there have been very few in which shaped holes were used with a typical turbine airfoil model. In this study, film effectiveness was measured on the suction side of a turbine blade model using two rows of 7-7-7 shaped holes, with pitch to diameter ratio of 6, and the two rows were more than 40 diameters apart. Measurements were made with each row operating independently, which provided the experimental data for superposition predictions. These predictions were evaluated with effectiveness measurements with both rows operational. For these combined row tests, two different upstream blowing ratios and a wide range of downstream blowing ratios were selected. The superposition predictions were reasonably accurate when the upstream blowing ratio was high with a corresponding smaller film effectiveness downstream (due to jet separation). However, when the upstream coolant holes were operated at optimum blowing ratio with maximum film effectiveness downstream, the superposition analysis predicted film effectiveness levels slightly lower than actual levels. These results indicate that there was an interaction between jets that resulted in higher film effectiveness than what the superposition method had predicted
Author: Shantanu Mhetras
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
Film cooling effectiveness on a gas turbine blade tip on the near tip pressure side and on the squealer cavity floor is investigated. Optimal arrangement of film cooling holes, effect of a full squealer and a cutback squealer, varying blowing ratios and squealer cavity depth are also examined on film cooling effectiveness. The film-cooling effectiveness distributions are measured on the blade tip, near tip pressure side and the inner pressure and suction side rim walls using a Pressure Sensitive Paint (PSP) technique. A blowing ratio of 1.0 is found to give best results on the pressure side whereas the other tip surfaces give best results for blowing ratios of 2. Film cooling effectiveness tests are also performed on the span of a fully-cooled high pressure turbine blade in a 5 bladed linear cascade using the PSP technique. Film cooling effectiveness over the entire blade region is determined from full coverage film cooling, showerhead cooling and from each individual row with and without an upstream wake. The effect of superposition of film cooling effectiveness from each individual row is then compared with full coverage film cooling. Results show that an upstream wake can result in lower film cooling effectiveness on the blade. Effectiveness magnitudes from superposition of effectiveness data from individual rows are comparable with that from full coverage film cooling. Internal heat transfer measurements are also performed in a high aspect ratio channel and from jet array impingement on a turbulated target wall at large Reynolds numbers. For the channel, three dimple and one discrete rib configurations are tested on one of the wide walls for Reynolds numbers up to 1.3 million. The presence of a turbulated wall and its effect on heat transfer enhancement against a smooth surface is investigated. Heat transfer enhancement is found to decrease at high Re with the discrete rib configurations providing the best enhancement but highest pressure losses. Experiments to investigate heat transfer and pressure loss from jet array impingement are also performed on the target wall at Reynolds numbers up to 450,000. The heat transfer from a turbulated target wall and two jet plates is investigated. A target wall with short pins provides the best heat transfer with the dimpled target wall giving the lowest heat transfer among the three geometries studied.
Author: National Aeronautics and Space Administration (NASA)
Publisher: Createspace Independent Publishing Platform
ISBN: 9781720482284
Category :
Languages : en
Pages : 64
Get Book Here
Book Description
The detailed heat transfer coefficient and film cooling effectiveness distributions as well as tile detailed coolant jet temperature profiles on the suction side of a gas turbine blade A,ere measured using a transient liquid crystal image method and a traversing cold wire and a traversing thermocouple probe, respectively. The blade has only one row of film holes near the gill hole portion on the suction side of the blade. The hole geometries studied include standard cylindrical holes and holes with diffuser shaped exit portion (i.e. fanshaped holes and laidback fanshaped holes). Tests were performed on a five-blade linear cascade in a low-speed wind tunnel. The mainstream Reynolds number based on cascade exit velocity was 5.3 x 10(exp 5). Upstream unsteady wakes were simulated using a spoke-wheel type wake generator. The wake Strouhal number was kept at 0 or 0.1. Coolant blowing ratio was varied from 0.4 to 1.2. Results show that both expanded holes have significantly improved thermal protection over the surface downstream of the ejection location, particularly at high blowing ratios. However, the expanded hole injections induce earlier boundary layer transition to turbulence and enhance heat transfer coefficients at the latter part of the blade suction surface. In general, the unsteady wake tends to reduce film cooling effectiveness.Han, J. C. and Teng, S.Glenn Research CenterHEAT TRANSFER COEFFICIENTS; COOLANTS; TEMPERATURE PROFILES; SUCTION; TURBINE BLADES; HEAT MEASUREMENT; FILM COOLING; BOUNDARY LAYER TRANSITION; CASCADE WIND TUNNELS; CYLINDRICAL BODIES; EJECTION; GAS TURBINES; HOLE DISTRIBUTION (MECHANICS); LIQUID CRYSTALS; LOW SPEED; THERMAL PROTECTION; THERMOCOUPLES; WIND TUNNELS
Author: Vijay K. Garg
Publisher:
ISBN:
Category :
Languages : en
Pages : 18
Get Book Here
Book Description
Author:
Publisher: Academic Press
ISBN: 0128124121
Category : Technology & Engineering
Languages : en
Pages : 336
Get Book Here
Book Description
Advances in Heat Transfer, Volume 49 provides in-depth review articles from a broader scope than in traditional journals or texts. Topics covered in this new volume include Heat Transfer in Rotating Cooling Channel, Flow Boiling and Flow Condensation in Reduced Gravity, Advances in Gas Turbine Cooling, and Advanced Heat Transfer Topics in Complex Duct Flows. While the articles in this series will be of great interest to mechanical, chemical and industrial engineers working in the field of heat transfer, the book is also ideal for those in graduate schools or industry, and even non-specialists interested in the latest research. Compiles the expert opinions of leaders in the industry Fills the information gap between regularly scheduled journals and university-level textbooks by providing in-depth review articles over a broader scope than in traditional journals or texts Essential reading for all mechanical, chemical and industrial engineers working in the field of heat transfer, or in graduate schools or industry
Author:
Publisher:
ISBN:
Category : Heat
Languages : en
Pages : 484
Get Book Here
Book Description
Author:
Publisher:
ISBN:
Category : Mechanical engineering
Languages : en
Pages : 574
Get Book Here
Book Description
Author: Kuo-Chun Liu
Publisher:
ISBN:
Category :
Languages : en
Pages :
Get Book Here
Book Description
The research focuses on testing the film cooling effectiveness on a gas turbine blade suction side surface. The test is performed on a five bladed cascade with a blow down facility. Four different blowing ratios are used in this study, which are 0.5, 1.0, 1.6, and 2.0; mainstream flow conditions are maintained at exit Mach number of 0.7, 1.1 and 1.3. Nitrogen is injected as the coolant so that the oxygen concentration levels can be obtained for the test surface. Based on mass transfer analogy, film cooling effectiveness can be computed with pressure sensitive paint (PSP) technique. The effect of blowing ratio on film cooling effectiveness is presented for each testing condition. The spanwise averaged effectiveness for each case is also presented to compare the blowing ratio and mainstream effect on film cooling effectiveness. Results show that due to effects of shock, the optimum blowing ratio is 1.6 for exit Mach number of 1.1 and 1.3; however; without the effects of shock, the optimum blowing ratio is 1.0 for exit Mach number of 0.7.
Author:
Publisher:
ISBN:
Category : Mechanical engineering
Languages : en
Pages : 556
Get Book Here
Book Description
Author: B. Sundén
Publisher: WIT Press
ISBN: 1853129569
Category : Science
Languages : en
Pages : 361
Get Book Here
Book Description
Providing invaluable information for both graduate researchers and R & D engineers in industry and consultancy, this book focuses on the modelling and simulation of fluid flow and thermal transport phenomena in turbulent convective flows. Its overall objective is to present state-of-the-art knowledge in order to predict turbulent heat transfer processes in fundamental and idealized flows as well as in engineering applications. The chapters, which are invited contributions from some of the most prominent scientists in this field, cover a wide range of topics and follow a unified outline and presentation to aid accessibility.
