Development and Characterization of Micro/nano Structured Surfaces for Enhanced Condensation PDF Download
Are you looking for read ebook online? Search for your book and save it on your Kindle device, PC, phones or tablets. Download Development and Characterization of Micro/nano Structured Surfaces for Enhanced Condensation PDF full book. Access full book title Development and Characterization of Micro/nano Structured Surfaces for Enhanced Condensation by Nenad Miljkovic. Download full books in PDF and EPUB format.
Author: Nenad Miljkovic
Publisher:
ISBN:
Category :
Languages : en
Pages : 185
Get Book Here
Book Description
Micro/nanostructures have long been recognized to have potential for heat transfer enhancement in phase-change processes by achieving extreme wetting properties, which is of great importance in a wide range of applications including thermal management, building environment control, water harvesting, desalination, and industrial power generation. This thesis focuses on the fundamental understanding of water vapor condensation on superhydrophobic surfaces, as well as the demonstration of such surfaces for enhanced condensation heat transfer performance. We first studied droplet-surface interactions during condensation on superhydrophobic surfaces to understand the emergent droplet wetting morphology. We demonstrated the importance of considering local energy barriers to understand the condensed droplet morphologies and showed nucleation-mediated droplet-droplet interactions can overcome these barriers to develop wetting states not predicted by global thermodynamic analysis. To minimize these droplet-droplet interactions and ensure the formation of favorable morphologies for enhanced condensation heat transfer, we show that the structure length scale needs to be minimized while ensuring the local energy barriers satisfy the morphology dependent criteria. This mechanistic understanding offers insight into the role of surface-structure length scale and provides a quantitative basis for designing surfaces optimized for condensation in engineered systems. Using our understanding of emergent droplet wetting morphology, we experimentally and numerically investigated the morphology dependent individual droplet growth rates. By taking advantage of well-controlled functionalized silicon nanopillars, the growth and shedding behavior of both suspended and partially wetting droplets on the same surface during condensation was observed. Environmental scanning electron microscopy was used to demonstrate that initial droplet growth rates of partially wetting droplets were 6 times larger than that of suspended droplets. A droplet growth model was developed to explain the experimental results and showed that partially wetting droplets had 4-6 times higher heat transfer rates than that of suspended droplets. Based on these findings, the overall performance enhancement created by surface nanostructuring was examined in comparison to a flat hydrophobic surface. These nanostructured surfaces had 56% heat flux enhancement for partially wetting droplet morphologies, and 71% heat flux degradation for suspended morphologies in comparison to flat hydrophobic surfaces. This study provides fundamental insights into the previously unidentified role of droplet wetting morphology on growth rate, as well as the need to design nanostructured surfaces with tailored droplet morphologies to achieve enhanced heat and mass transfer during dropwise condensation. To create a unified model for condensation capable of predicting the surface heat transfer for a variety of surface length scales, geometries, and condensation conditions, we incorporated the emergent droplet wetting morphology, individual droplet heat transfer, and size distribution. The model results showed a specific range of characteristic length scales (0.5 - 2 ptm) allowing for the formation of coalescence-induced jumping droplets with a 190% overall surface heat flux enhancement over conventional flat dropwise condensing surfaces. This work provided a unified model for dropwise condensation on micro/nanostructured superhydrophobic surfaces and offered guidelines for the selection of ideal structured surfaces to maximize heat transfer. Using the insights gained from the developed model and optimization, a scalable synthesis technique was developed to produce functionalized oxide nanostructures on copper surfaces capable of sustaining superhydrophobic condensation. Nanostructured copper oxide (CuO) films were formed via chemical oxidation in an alkaline solution resulting in dense arrays of sharp CuO nanostructures with characteristic heights and widths of -1 pm and -300 nm, respectively. Condensation on these surfaces was characterized using optical microscopy and environmental scanning electron microscopy to quantify the distribution of nucleation sites and elucidate the growth behavior of individual droplets with characteristic radii of -1 to 10 pm at supersaturations
Author: Nenad Miljkovic
Publisher:
ISBN:
Category :
Languages : en
Pages : 185
Get Book Here
Book Description
Micro/nanostructures have long been recognized to have potential for heat transfer enhancement in phase-change processes by achieving extreme wetting properties, which is of great importance in a wide range of applications including thermal management, building environment control, water harvesting, desalination, and industrial power generation. This thesis focuses on the fundamental understanding of water vapor condensation on superhydrophobic surfaces, as well as the demonstration of such surfaces for enhanced condensation heat transfer performance. We first studied droplet-surface interactions during condensation on superhydrophobic surfaces to understand the emergent droplet wetting morphology. We demonstrated the importance of considering local energy barriers to understand the condensed droplet morphologies and showed nucleation-mediated droplet-droplet interactions can overcome these barriers to develop wetting states not predicted by global thermodynamic analysis. To minimize these droplet-droplet interactions and ensure the formation of favorable morphologies for enhanced condensation heat transfer, we show that the structure length scale needs to be minimized while ensuring the local energy barriers satisfy the morphology dependent criteria. This mechanistic understanding offers insight into the role of surface-structure length scale and provides a quantitative basis for designing surfaces optimized for condensation in engineered systems. Using our understanding of emergent droplet wetting morphology, we experimentally and numerically investigated the morphology dependent individual droplet growth rates. By taking advantage of well-controlled functionalized silicon nanopillars, the growth and shedding behavior of both suspended and partially wetting droplets on the same surface during condensation was observed. Environmental scanning electron microscopy was used to demonstrate that initial droplet growth rates of partially wetting droplets were 6 times larger than that of suspended droplets. A droplet growth model was developed to explain the experimental results and showed that partially wetting droplets had 4-6 times higher heat transfer rates than that of suspended droplets. Based on these findings, the overall performance enhancement created by surface nanostructuring was examined in comparison to a flat hydrophobic surface. These nanostructured surfaces had 56% heat flux enhancement for partially wetting droplet morphologies, and 71% heat flux degradation for suspended morphologies in comparison to flat hydrophobic surfaces. This study provides fundamental insights into the previously unidentified role of droplet wetting morphology on growth rate, as well as the need to design nanostructured surfaces with tailored droplet morphologies to achieve enhanced heat and mass transfer during dropwise condensation. To create a unified model for condensation capable of predicting the surface heat transfer for a variety of surface length scales, geometries, and condensation conditions, we incorporated the emergent droplet wetting morphology, individual droplet heat transfer, and size distribution. The model results showed a specific range of characteristic length scales (0.5 - 2 ptm) allowing for the formation of coalescence-induced jumping droplets with a 190% overall surface heat flux enhancement over conventional flat dropwise condensing surfaces. This work provided a unified model for dropwise condensation on micro/nanostructured superhydrophobic surfaces and offered guidelines for the selection of ideal structured surfaces to maximize heat transfer. Using the insights gained from the developed model and optimization, a scalable synthesis technique was developed to produce functionalized oxide nanostructures on copper surfaces capable of sustaining superhydrophobic condensation. Nanostructured copper oxide (CuO) films were formed via chemical oxidation in an alkaline solution resulting in dense arrays of sharp CuO nanostructures with characteristic heights and widths of -1 pm and -300 nm, respectively. Condensation on these surfaces was characterized using optical microscopy and environmental scanning electron microscopy to quantify the distribution of nucleation sites and elucidate the growth behavior of individual droplets with characteristic radii of -1 to 10 pm at supersaturations
Author: Emre Olceroglu
Publisher:
ISBN:
Category : Heat
Languages : en
Pages : 258
Get Book Here
Book Description
Because of their adjustable wetting characteristics, micro/nanostructured surfaces are attractive for the enhancement of phase-change heat transfer where liquid-solid-vapor interactions are important. Condensation, evaporation, and boiling processes are traditionally used in a variety of applications including water harvesting, desalination, industrial power generation, HVAC, and thermal management systems. Although they have been studied by numerous researchers, there is currently a lack of understanding of the underlying mechanisms by which structured surfaces improve heat transfer during phase-change. This PhD dissertation focuses on condensation onto engineered surfaces including fabrication aspect, the physics of phase-change, and the operational limitations of engineered surfaces. While superhydrophobic condensation has been shown to produce high heat transfer rates, several critical issues remain in the field. These include surface manufacturability, heat transfer coefficient measurement limitations at low heat fluxes, failure due to surface flooding at high supersaturations, insufficient modeling of droplet growth rates, and the inherent issues associated with maintenance of non-wetted surface structures. Each of these issues is investigated in this thesis, leading to several contributions to the field of condensation on engineered surfaces. A variety of engineered surfaces have been fabricated and characterized, including nanostructured and hierarchically-structured superhydrophobic surfaces. The Tobacco mosaic virus (TMV) is used here as a biological template for the fabrication of nickel nanostructures, which are subsequently functionalized to achieve superhydrophobicity. This technique is simple and sustainable, and requires no applied heat or external power, thus making it easily extendable to a variety of common heat transfer materials and complex geometries. To measure heat transfer rates during superhydrophobic condensation in the presence of non-condensable gases (NCGs), a novel characterization technique has been developed based on image tracking of droplet growth rates. The full-field dynamic characterization of superhydrophobic surfaces during condensation has been achieved using high-speed microscopy coupled with image-processing algorithms. This method is able to resolve heat fluxes as low as 20 W/m2 and heat transfer coefficients of up to 1000 kW/m2, across an array of 1000's of microscale droplets simultaneously. Nanostructured surfaces with mixed wettability have been used to demonstrate delayed flooding during superhydrophobic condensation. These surfaces have been optimized and characterized using optical and electron microscopy, leading to the observation of self-organizing microscale droplets. The self-organization of small droplets effectively delays the onset of surface flooding, allowing the superhydrophobic surfaces to operate at higher supersaturations. Additionally, hierarchical surfaces have been fabricated and characterized showing enhanced droplet growth rates as compared to existing models. This enhancement has been shown to be derived from the presence of small feeder droplets nucleating within the microscale unit cells of the hierarchical surfaces. Based on the experimental observations, a mechanistic model for growth rates has been developed for superhydrophobic hierarchical surfaces. While superhydrophobic surfaces exhibit high heat transfer rates they are inherently unstable due to the necessity to maintain a non-wetted state in a condensing environment. As an alternative condensation surface, a novel design is introduced here using ambiphilic structures to promote the formation of a thin continuous liquid film across the surface which can still provide the benefits of superhydrophobic condensation. Preliminary results show that the ambiphilic structures restrain the film thickness, thus maintaining a low thermal resistance while simultaneously maximizing the liquid-vapor interface available for condensation.
Author: Jean Hope Sack
Publisher:
ISBN:
Category :
Languages : en
Pages : 58
Get Book Here
Book Description
Increasing worldwide and domestic demands for power and clean water will require advanced heat transfer materials. Superhydrophobic micro- and nano-structured surfaces which promote a jumping droplet mode of condensation have been shown to enhance heat transfer over conventional film wise condensation surfaces, but limited robustness testing has been reported validating feasibility of industrial implementation. This thesis seeks to quantify the robustness of a variety of nanostructures, substrates and coatings by analyzing contact angle measurements and SEM imaging over the course of accelerated robustness testing. This testing was enabled through the design and construction of three custom-built setups intended to accelerate the onset of failure mechanisms. These setups consist of a flow setup to observe resistance to shear flows from internal condensation steam flow, a droplet impingement setup to test mechanical durability, and an elevated temperature condensation chamber to characterize thermal stability. Methods for fabricating nanostructures were also developed, and scalable zinc oxide nanowires (ZnO) and copper oxide nanoblades (CuO) were used. CuO nanoblades were etched into copper, and ZnO nanowires were grown on silicon, low carbon steel, titanium, stainless steel, and electroplated nickel. Hydrophobic coatings tested on these surfaces included stearic acid and two polymer coatings: P2i (40nm) and Semblant. Observed failure mechanisms were coating degradation and poor nanostructure adhesion. Nanostrucure adhesion issues were observed as delamination of ZnO nanowires primarily on stainless steel substrates. Adhesion was improved through the addition of an electroplated nickel layer before nanowire growth, but delamination was still observed. This is likely the result a large mismatch in coefficient of thermal expansion between the ZnO nanowires and the substrate. The etched CuO nanostructures with a fluorinated polymer coating (P2i) showed very little change in performance throughout robustness testing. Characterization methods included contact angle measurements to monitor surface uniformity and durability, and scanning electron microscope (SEM) imaging to observe nanostructure degradation and delamination. Preliminary work was also done to functionalize the inside of tubes and design a dedicated test setup to characterize heat transfer measurements for internal jumping condensation. This setup will allow for extended robustness testing over a range of temperatures, pressures, and geometries, and give baseline heat flux values for comparison with dropwise or filmwise internal condensation. While ZnO nanowires still require additional testing and development, CuO nanoblades are good candidates for internal heat transfer measurements and scaled up robustness testing. Assuming this characterization confirms the expected benefits of jumping condensation from increased droplet removal and nucleation density, this technology has the potential to significantly improve power plant efficiency and output worldwide.
Author: Changho Choi
Publisher:
ISBN:
Category : Ebullition
Languages : en
Pages : 146
Get Book Here
Book Description
This objective of this study is to investigate the capability of nanostructured surfaces on dissipating heat flux by performing pool boiling and convective flow boiling. The generation of ultra-high heat flux from high performance electric devices has motivated a number of investigations related to advanced heat transfer especially in two-phase boiling performance. It has been reported by a number of researchers that nanostructured surfaces can result in much enhanced boiling performance, compared to the conventional methods by creating desire conditions for heat transfer. In this thesis, various nanostructured surfaces having different morphology were prepared on several engineering relevant substrates and were characterized for their pool boiling performance. Microreactor-assisted-nanomaterial-deposition, MAND [trademark symbol] was used to fabricate a variety of different ZnO nanostructured surfaces by careful adjustment of the processing parameters. ZSM-5 zeolite was synthesized using hydrothermal reaction. ZnO nanostructures in minichannel were also successfully deposited via a flow cell for the application of flow boiling experiment. Scanning electron microscopy (SEM) and Atomic Force Microscopy (AFM) were carried out to characterize the micro- and nanostructures. Contact angle measurement was conducted to evaluate wettability and X-ray Diffraction (XRD) was used to determine the crystalline structures. The most significant enhancement of critical heat flux (CHF) and heat transfer coefficient (HTC) was observed in the flower like ZnO nanostructured surface. We observed pool boiling CHF of 80-82.5 W/cm2 for nanostructured ZnO on Al surfaces versus a CHF of 23.2 W/cm2 on a bare Al surface with a wall superheat reduction of 25-38°C. This new CHF values on nanostructured surfaces corresponds to a boiling heat transfer coefficient as high as ~ 23000 W/m2K. This represents an increase of almost 4X in CHF on nano-textured surfaces, which is the highest enhancement factor reported today.
Author: Kuang-Han Chu (Ph. D.)
Publisher:
ISBN:
Category :
Languages : en
Pages : 65
Get Book Here
Book Description
Two-phase microchannel heat sinks are of significant interest for thermal management applications, where the latent heat of vaporization offers an efficient method to dissipate large heat fluxes in a compact device. However, a significant challenge for the implementation of microchannel heat sinks is associated with flow instabilities due to insufficient bubble removal, leading to liquid dry-out which severely limits the heat removal efficiency. To address this challenge, we propose to incorporate micro/nanostructures to stabilize and enhance two-phase microchannel flows. Towards this goal, this thesis focuses on fundamental understanding of micro/nanostructures to manipulate liquid and vapor bubble dynamics, and to improve overall microchannel heat transfer performance. We first investigated the role of micro/nanostructure geometry on liquid transport behavior. We designed and fabricated asymmetric nanostructured surfaces where nanopillars are deflected with angles ranging from 7 -52'. Uni-directional liquid spreading was demonstrated where the liquid propagates in a single preferred direction and pins in all others. Through experiments and modeling, we determined that the spreading characteristic is dependent on the degree of nanostructure asymmetry, height-to-spacing ratio of the nanostructures, and intrinsic contact angle. The theory, based on an energy argument, provides excellent agreement with experimental data. This work shows a promising method to manipulate liquid spreading with structured surfaces, which potentially can also be used to manipulate vapor bubble dynamics. We subsequently investigated the effect of micro/nanostructured surface design on vapor bubble dynamics and pool boiling heat transfer. We fabricated micro-, nano-, and hierarchically-structured surfaces with a wide range of well-defined surface roughness factors and measured the heat transfer characteristics. The maximum critical heat flux (CHF) was ~250 W/cm2 with a roughness factor of~-13.3. We also developed a force-balance based model, which shows excellent agreement with the experiments. The results demonstrate the significant effect of surface roughness at capillary length scales on enhancing CHF. This work is an important step towards demonstrating the promising role of surface design for enhanced two-phase heat transfer. Finally, we investigated the heat transfer performance of microstructured surfaces incorporated in microchannel devices with integrated heaters and temperature sensors. We fabricated silicon micropillars with heights of 25 [mu]m, diameters of 5-10 [mu]m and spacings of 5- 10 [mu]m in microchannels of 500 [mu]m x 500 [mu]m. We characterized the performance of the microchannels with a custom closed loop test setup. This thesis provides improved fundamental understanding of the role of micro/nanostructures on liquid spreading and bubble dynamics as well as the practical implementation of such structures in microchannels for enhanced heat transfer. This work serves as an important step towards realizing high flux two-phase microchannel heat sinks for various thermal management applications.
Author: Hans-Jörg Bart
Publisher: Springer
ISBN: 3319716417
Category : Science
Languages : en
Pages : 398
Get Book Here
Book Description
This accessible book presents unconventional technologies in heat exchanger design that have the capacity to provide solutions to major concerns within the process and power-generating industries. Demonstrating the advantages and limits of these innovative heat exchangers, it also discusses micro- and nanostructure surfaces and micro-scale equipment, and introduces pillow-plate, helical and expanded metal baffle concepts. It offers step-by-step worked examples, which provide instructions for developing an initial configuration and are supported by clear, detailed drawings and pictures. Various types of heat exchangers are available, and they are widely used in all fields of industry for cooling or heating purposes, including in combustion engines. The market in 2012 was estimated to be U$ 42.7 billion and the global demand for heat exchangers is experiencing an annual growth of about 7.8 %. The market value is expected to reach U$ 57.9 billion in 2016, and approach U$ 78.16 billion in 2020. Providing a valuable introduction to students and researchers, this book offers clear and concise information to thermal engineers, mechanical engineers, process engineers and heat exchanger specialists.
Author: Phuong Pham
Publisher: BoD – Books on Demand
ISBN: 1789851998
Category : Technology & Engineering
Languages : en
Pages : 295
Get Book Here
Book Description
Surface sciences elucidate the physical and chemical aspects of the surfaces and interfaces of materials. Of great interest in this field are nanomaterials, which have recently experienced breakthroughs in synthesis and application. As such, this book presents some recent representative achievements in the field of surface science, including synthesis techniques, surface modifications, nanoparticle-based smart coatings, wettability of different surfaces, physics/chemistry characterizations, and growth kinetics of thin films. In addition, the book illustrates some of the important applications related to silicon, CVD graphene, graphene oxide, transition metal dichalcogenides, carbon nanotubes, carbon nanoparticles, transparent conducting oxide, and metal oxides.
Author: Ali Sadaghiani
Publisher: Academic Press
ISBN: 0128169249
Category : Technology & Engineering
Languages : en
Pages : 259
Get Book Here
Book Description
Nanofluid Boiling presents valuable insights into boiling heat transfer mechanisms, offering state-of-the-art techniques for overcoming obstacles against nanofluid applications. In addition, the book points out emerging industrial applications and guides researchers and engineers in their research and design efforts. In addition, recommendations on future research directions and the design of systems involving nanofluids are presented at the end of each chapter. The book's authors comprehensively cover mechanisms, parametric effects and enhancement techniques in the boiling of nanofluids, providing updated, detailed information about recent developments and findings. Reveals insights into the findings and mechanisms of boiling heat transfer in nanofluids, guiding researchers and engineers in their research and design efforts Focuses on parametric effects such as nanofluid properties (size, concentration, nanoparticle type), preparation methods on heat transfer and critical heat flux mechanisms, bubble dynamics, flow patterns, and pressure drop Presents readers with scaling effects (from macro to microscale) relevant to nanofluid boiling
Author: Simon J. Leigh
Publisher:
ISBN:
Category :
Languages : en
Pages : 284
Get Book Here
Book Description
Author: Rong Xiao (Ph. D.)
Publisher:
ISBN:
Category :
Languages : en
Pages : 76
Get Book Here
Book Description
Micro/nanostructures have been extensively studied to amplify the intrinsic wettability of materials to create superhydrophilic or superhydrophobic surfaces. Such extreme wetting properties can influence the heat transfer performance during phase-change which is of great importance in a wide range of applications including thermal management, building environment, water harvesting and power production. In particular, superhydrophilic surfaces have been of interest to achieve thin film evaporation with high heat fluxes. Meanwhile, superhydrophobic surfaces with dropwise condensation promises higher heat transfer coefficients than typical filmwise condensation. My thesis work aims at improving fundamental understanding as well as demonstrating practical enhancements in these two areas. A key challenge to realizing thin film evaporation is the ability to achieve efficient fluid transport using superhydrophilic surfaces. Accordingly, we developed a semi-analytical model based on the balance between capillary pressure and viscous resistance to predict the propagation rates in micropillar arrays with high aspect ratios. Our experimental results showed good agreement with the model, and design guidelines for optimal propagation rates were proposed. For micropillar arrays with low aspect ratio and large spacing between pillars, however, we identified that the microscopic sweeping of the liquid front becomes important. We studied this phenomenon, explained the effect of such microscale dynamics on the overall propagation behavior, and proposed a strategy to account for these dynamics. While these propagation studies provide a means to deliver liquid to high heat flux regions, we investigated a different configuration using nanoporous membrane that decouples capillarity from the viscous resistance to demonstrate the potential heat dissipation capability. With nanoporous membranes with average pore diameters of 150 nm and thicknesses of 50 [mu]m, we achieved interfacial heat fluxes as high as 96 W/cm2 via evaporation with isopropyl alcohol. The effect of membrane thickness was studied to offer designs that promise dissipation of 1000 W/cm 2 . Meanwhile, we developed new metrology to measure transient heat transfer coefficients with a temporal resolution of 0.2 seconds during the evaporation process. Such a technique offers insight into the relationship between liquid morphology and heat transfer behavior. Finally, for enhanced condensation, we demonstrated immersion condensation using a composite surface fabricated by infusing hydrophobic oil into micro/nanostructures with a heterogeneous coating. With this approach, three key attributes to maximize heat transfer coefficient, low departure radii, low contact angle, and high nucleation density, were achieved simultaneously. We specifically elucidated the mechanism for the increase in nucleation density and attribute it to the combined effect of reduced water-oil interfacial energy and local high surface energy sites. As a result, we demonstrated approximately 100% enhancement in heat transfer coefficient over state-of-the-art superhydrophobic surfaces with the presence of non-condensable gases. This thesis presents improved fundamental understanding of wetting, evaporation, and condensation processes on micro/nanostructures as well as practical implementation of these structures for enhanced heat transfer. The insights gained demonstrate the potential of new nanostructure engineering approaches to improve the performance of various thermal management and energy production applications.
